Lexicon MC-12 Digital Controller Lexicon MC-12 - Manual (Page 174)

Appendix
MC-12
A-11
MAIN MENU
MODE ADJUST
AUDIO CONTROLS
SETUP
SETUP
SETUP
INPUTS
SPEAKERS
REAR PANEL CONFIG
DISPLAYS
VOLUME CONTROLS
TRIGGERS
LOCK OPTIONS
SPEAKERS
AUTO SPEAKER SETUP
DISTANCES & LEVELS
DISTANCES
OUTPUT LEVELS
PLACE MICROPHONES
IN PRIMARY LISTENING
POSITIONS
DISTANCES & LEVELS
AUTO SPEAKER SETUP
TEST WILL BEGIN IN
10
PRESS V TO SKIP
COUNTDOWN
AUTO SPEAKER SETUP
!CAUTION!
HIGH AUDIO LEVELS
YOU WILL HAVE 10 SEC
TO LEAVE THE ROOM OR
SIT QUIETLY
PRESS V TO BEGIN
COUNTDOWN
10
AUTO SPEAKER SETUP
DISTANCES OK
LEVELS OK
AUTO VALUES APPLIED
PRESS V TO VIEW
DETAILS
AUTO SPEAKER SETUP
DISTANCES ERROR
LEVELS ERROR
AUTO VALUES APPLIED
PRESS V TO VIEW
DETAILS
SETTING DISTANCES
FRONT LEFT 0.0ft
CENTER 0.0ft
FRONT RIGHT 0.0ft
SIDE RIGHT 0.0ft
REAR RIGHT 0.0ft
REAR LEFT 0.0ft
SIDE LEFT 0.0ft
MONO SUB 0.0ft
SUB RIGHT N/A
LFE N/A
SETTING LEVELS
FRONT LEFT +0.0dB
CENTER +0.0dB
FRONT RIGHT +0.0dB
SIDE RIGHT +0.0dB
REAR RIGHT +0.0dB
REAR LEFT +0.0dB
SIDE LEFT +0.0dB
MONO SUB +0.0dB
SUB RIGHT N/A
LFE N/A
MIC CHECK REQUIRED
FOR AUTO CALIBRATION
AUTO LEVELS
FRONT LEFT ERROR
CENTER +0.0dB
FRONT RIGHT +0.0dB
SIDE RIGHT +0.0dB
REAR RIGHT +0.0dB
REAR LEFT +0.0dB
SIDE LEFT +0.0dB
MONO SUB +0.0dB
SUB RIGHT N/A
LFE N/A
FRONT LEFT ERROR
(SPEAKER)
SPKR OUTPUT TOO LOW
(SPEAKER)
UNABLE TO CALCULATE
(SPEAKER)
OK
LEVELS
OK
DISTANCES
OK
(SPEAKER)
SPEAKER IS NOT ENABLED
(SPEAKER)
SPKR OUTPUT TOO HIGH
AUTO DISTANCES
FRONT LEFT ERROR
CENTER 0.0ft
FRONT RIGHT 0.0ft
SIDE RIGHT 0.0ft
REAR RIGHT 0.0ft
REAR LEFT 0.0ft
SIDE LEFT 0.0ft
MONO SUB 0.0ft
SUB RIGHT N/A
LFE N/A
FRONT LEFT ERROR
(SPEAKER)
SIGNAL TOO LOW
(SPEAKER)
OK
(SPEAKER)
SPEAKER IS NOT ENABLED
(SPEAKER)
SPEAKER OUT OF PHASE
or
SPEAKER SETUP
SET CROSSOVERS
CHECK MICROPHONES
AUTOMATIC
MANUAL
SET CROSSOVERS
BEFORE CALIBRATING
AUTOMATIC
When the MC-12 is finished calibrating speaker
distances and output levels, the AUTO SPEAKER
SETUP results screen shown at the left will open on
the on-screen display, indicating the results for each
calibration procedure. Press the
and arrow
buttons to highlight the desired calibration procedure.
Then, press the
arrow button to select this procedure.
Selecting DISTANCES opens the AUTO DISTANCES
screen shown below. Selecting the LEVELS option
opens the AUTO LEVELS screen shown below.
The AUTO DISTANCES and AUTO LEVELS screens
shown at the right indicate the individual calibration
results for each speaker. Press the
and arrow
buttons to highlight the desired speaker calibration
parameter. Then, press the
arrow button to view
more detailed results for the selected speaker.
Press the arrow button to return to the AUTO
SPEAKER SETUP results screen shown above (right).
Then, press the
arrow button to select the other
calibration procedure or press the the arrow button
to return to the SPEAKER SETUP menu.
(SPEAKER)
MAY NOT BE ACCURATE