Lincoln Electric POWER MIG 11521 - Manual (Page 24)

ACCESSORIES C-2 C-2
Power MIG® 215XT
DRIVE ROLL KITS
Refer to Table C.1 for various drive roll kits that are
available for the POWER MIG® 215XT. The item in
Bold is supplied standard with the POWER MIG®
215XT.
TABLE C.1
3/64" (1.2 mm) ALUMINUM
FEEDING KIT (K1703-1)
This kit helps push feeding aluminum through standard
machine feeder and gun. It provides gun and wire drive
conversion parts to weld with 3/64" (1.2 mm) aluminum
wire. 5356 alloy aluminum wire is recommended for
best push feeding performance.
Kit includes drive rolls and wire guide plate for the wire
drive, liner and two contact tips for the gun, along with
installation instructions.
READI-REEL ADAPTER (K363P)
The K363P Readi-Reel Adapter mounts to the 2" spin-
dle. It is needed to mount the 22-30 lb. Readi-Reels.
DUAL CYLINDER MOUNTING KIT
(K1702-1)
Permits stable side-by-side mounting of two full size
228.6mm dia x 1.524m high(9" dia. x 5' high) gas cylin-
ders with “no lift” loading. Simple installation and easy
instructions provided. Includes upper and lower cylin-
der supports, wheel axles and mounting hardware.
SMALL SPOOL SPINDLE ADAPTER
(K468)
The K468 spindle adapter allows the use of 8" diame-
ter small spools.
ALTERNATIVE MAGNUM GMAW
GUN AND CABLE ASSEMBLIES
The following Magnum 250L gun and cable assemblies
are separately available for use with the POWER
MIG® 215XT. Each is rated 250 amps 40% duty cycle
and is equipped with the integrated connector, twist-
lock trigger connector, fixed nozzle and insulator, and
includes a liner, diffuser, and contact tips for the wire
sizes specified:
• Unplug or Disconnect all input
power from the POWER MIG® 215XT
before installing the Spool Gun and
Kit.
------------------------------------------------------------------------
MAGNUM GUN CONNECTION KIT
(Optional K466-6)
Using the optional K466-6 Magnum Connection kit for
the POWER MIG® 215XT permits use of standard
Magnum 200, 300 or 400 gun and cable assemblies.
OPTIONAL SPOOL GUNS AND
ADAPTERS
The Power MIG® 215XT is capable of operating with the fol-
lowing optional spool guns:
Spool gun Adapter (K2703-1)
This kit is designed to allow the Magnum SG or Magnum
250LX spool gun to operate with the Power MIG® 215XT.
The kit includes the solenoid, gas lines, wiring harness and
gun connection panel. The gun connection panel features a
6 pin ms-type connector for the Magnum SG spool gun and
a 7 pin ms-type connector for the Magnum 250LX spool gun
and a selector switch to choose which gun you are using.
Note the K2703-1 spool gun adapter disables the
Magnum 100SG capability.
Wire Size Drive Roll Kit
.023”-.030” (0.6-0.8 mm) KP1696-030S
.035” (0.9 mm) KP1696-035S
Solid
.045” (1.2 mm) KP1696-045S
Steel
.035-.045 (0.9-1.2mm) KP1696-1
.040 (1.01) KP1696-2
Cored
.035” (0.9 mm) KP1697-035C
.045” (1.2 mm) KP1697-045C
Aluminum 3/64” (1.2 mm) KP1695-3/64A
English Wire Metric Wire
Length Part No. Size Size
10' (3.0 m) K533-1
12' (3.6 m) K533-7 .035 – .045" 0.9 – 1.2 mm
15' (4.5 m) K533-3
SPOOL GUN
Magnum 100SG
(K2532-1)
Magnum SG
(K487-25)
Magnum 250LX
(K2490-1)
ADAPTER
Factory Capable
No Adapter Required
Spool Gun Adapter
K2703-1
RATING
Light Duty
130amp 30% Duty Cycle
Medium Duty
250Amp 60% Duty Cycle
Heavy Duty
300 Amp 60% Duty Cycle
WARNING
Return
to
Section
T
OC
Return
to
Section
T
OC
Return
to
Section
T
OC
Return
to
Section
T
OC
Return
to
Master
T
OC
Return
to
Master
T
OC
Return
to
Master
T
OC
Return
to
Master
T
OC