Renesas R61509V - Manual (Page 87)

R61509V Target Spec
Rev. 0.11 April 25, 2008, page 87 of 181
Table 54
Gate scan start position
SM=0 SM=1 SCN[5:0]
GS=0 GS=1 GS=0 GS=1
6’h00 G1 G(N) G1 G(2N-432)
6’h01 G9 G(N+8) G17 G(2N-416)
6’h02 G17 G(N+16) G33 G(2N-400)
6’h03 G25 G(N+24) G49 G(2N-384)
6’h04 G33 G(N+32) G65 G(2N-368)
6’h05 G41 G(N+40) G81 G(2N-352)
6’h06 G49 G(N+49) G97 G(2N-336)
6’h07 G57 G(N+56) G113 G(2N-320)
6’h08 G65 G(N+64) G129 G(2N-304)
6’h09 G73 G(N+72) G145 G(2N-288)
6’h0A G81 G(N+80) G161 G(2N-272)
6’h0B G89 G(N+88) G177 G(2N-256)
6’h0C G97 G(N+96) G193 G(2N-240)
6’h0D G105 G(N+104) G209 G(2N-224)
6’h0E G113 G(N+112) G225 G(2N-208)
6’h0F G121 G(N+120) G241 G(2N-192)
6’h10 G129 G(N+128) G257 G(2N-176)
6’h11 G137 G(N+136) G273 G(2N-160)
6’h12 G145 G(N+144) G289 G(2N-144)
6’h13 G153 G(N+152) G305 G(2N-128)
6’h14 G161 G(N+160) G321 G(2N-112)
6’h15 G169 G(N+168) G337 G(2N-96)
6’h16 G177 G(N+176) G353 G(2N-80)
6’h17 G185 G(N+184) G369 G(2N-64)
6’h18 G193 G(N+192) G385 G(2N-48)
6’h19 G201 G(N+200) G401 G(2N-32)
6’h1A G209 G(N+208) G417 G(2N-16)
6’h1B G217 G(N+216) G2 G(2N-431)
6’h1C G225 G(N+224) G18 G(2N-415)
6’h1D G233 G(N+232) G34 G(2N-399)
6’h1E G241 G(N+240) G50 G(2N-383)
6’h1F G249 G(N+248) G66 G(2N-367)
6’h20 G257 G(N+256) G82 G(2N-351)
6’h21 G265 G(N+264) G98 G(2N-335)
6’h22 G273 G(N+272) G114 G(2N-319)
6’h23 G281 G(N+280) G130 G(2N-303)
6’h24 G289 G(N+288) G146 G(2N-287)
6’h25 G297 G(N+296) G162 G(2N-271)
6’h26 G305 G(N+304) G178 G(2N-255)
6’h27 G313 G(N+312) G194 G(2N-239)
6’h28 G321 G(N+320) G210 G(2N-223)
6’h29 G329 G(N+328) G226 G(2N-207)
6’h2A G337 G(N+337) G242 G(2N-191)
6’h2B G345 G(N+344) G258 G(2N-175)
6’h2C G353 G(N+352) G274 G(2N-159)
6’h2D G361 G(N+360) G290 G(2N-143)
6’h2E G369 G(N+368) G306 G(2N-127)
6’h2F G377 G(N+376) G322 G(2N-111)
6’h30 G385 G(N+384) G338 G(2N-95)
6’h31 G393 G(N+392) G354 G(2N-79)
6’h32 G401 G(N+400) G370 G(2N-63)
6’h33 G409 G(N+408) G386 G(2N-47)
6’h34 G417 G(N+416) G402 G(2N-31)
6’h35-6’h3F Setting inhibited Setting inhibited Setting inhibited Setting inhibited
Note: “N” is the number of line decided by NL [5:0] bit.
Make sure that (Gate scan start position + NL = Gate scan end position) does not exceed 432 lines.