Texas Instruments Dual/Single Socket CardBus and UntraMedia Controller PCI7621 - Manual (Page 208)

8−28
8.31 Link Control Register
The link control set/clear register provides the control flags that enable and configure the link core protocol portions
of the PCI7x21/PCI7x11 controller. It contains controls for the receiver and cycle timer. See Table 8−23 for a complete
description of the register contents.
Bit 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
Name Link control
Type R R R R R R R R R RSC RSCU RSC R R R R
Default 0 0 0 0 0 0 0 0 0 X X X 0 0 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Name Link control
Type R R R R R RSC RSC R R RS R R R R R R
Default 0 0 0 0 0 X X 0 0 0 0 0 0 0 0 0
Register: Link control
Offset: E0h set register
E4h clear register
Type: Read/Set/Clear/Update, Read/Set/Clear, Read-only
Default: 00X0 0X00h
Table 8−23. Link Control Register Description
BIT FIELD NAME TYPE DESCRIPTION
31−23 RSVD R Reserved. Bits 31−23 return 0s when read.
22 cycleSource RSC When bit 22 is set to 1, the cycle timer uses an external source (CYCLEIN) to determine when to roll
over the cycle timer. When this bit is cleared, the cycle timer rolls over when the timer reaches
3072 cycles of the 24.576-MHz clock (125
µ s).
21 cycleMaster RSCU When bit 21 is set to 1, the PCI7x21/PCI7x11 controller is root and it generates a cycle start packet
every time the cycle timer rolls over, based on the setting of bit 22 (cycleSource). When bit 21 is
cleared, the OHCI-Lynx
 accepts received cycle start packets to maintain synchronization with the
node which is sending them. Bit 21 is automatically cleared when bit 25 (cycleTooLong) in the
interrupt event register at OHCI offset 80h/84h (see Section 8.21) is set to 1. Bit 21 cannot be set to
1 until bit 25 (cycleTooLong) is cleared.
20 CycleTimerEnable RSC When bit 20 is set to 1, the cycle timer offset counts cycles of the 24.576-MHz clock and rolls over
at the appropriate time, based on the settings of the above bits. When this bit is cleared, the cycle
timer offset does not count.
19−11 RSVD R Reserved. Bits 19−11 return 0s when read.
10 RcvPhyPkt RSC When bit 10 is set to 1, the receiver accepts incoming PHY packets into the AR request context if
the AR request context is enabled. This bit does not control receipt of self-identification packets.
9 RcvSelfID RSC When bit 9 is set to 1, the receiver accepts incoming self-identification packets. Before setting this
bit to 1, software must ensure that the self-ID buffer pointer register contains a valid address.
8−7 RSVD R Reserved. Bits 8 and 7 return 0s when read.
6 ‡ tag1SyncFilterLock RS When bit 6 is set to 1, bit 6 (tag1SyncFilter) in the isochronous receive context match register (see
Section 8.46) is set to 1 for all isochronous receive contexts. When bit 6 is cleared, bit 6
(tag1SyncFilter) in the isochronous receive context match register has read/write access. This bit is
cleared when GRST is asserted.
5−0 RSVD R Reserved. Bits 5−0 return 0s when read.
‡ This bit is cleared only by the assertion of GRST.