Yamaha MOTIF XS7 EN - Manual (Page 290)

Troubleshooting
MOTIF XS Owner’s Manual 290
Appendix
Only one note sounds at a time.
■ When this situation occurs, the Mono/Poly parameter in the current mode is set to “mono.” If you wish to play chords, set this
parameter to “poly.”
Pitch or intervals are wrong.
■ Is the Master Tune parameter in the Utility mode set to a value other than “0”?
■ Is the Note Shift parameter in the Utility mode set to a value other than “0”?
■ When the voice produces a wrong pitch, is the appropriate tuning system selected from Micro Tuning parameter in the Voice Edit
mode?
■ When the Voice produces a wrong pitch, is the LFO Pitch Modulation Depth in the Voice Edit mode set too high?
■ When the Performance/Song/Pattern produces a wrong pitch, is the Note Shift parameter of each Part set to a value other than
“0”?
■ When the Song/Pattern playback produces a wrong pitch, is the Note Shift parameter in the Play FX display set to a value other
than “0”?
No effect is applied.
■ Is the [EFFECT BYPASS] button turned off? (page 13)
■ Have the REVERB and CHORUS knobs been turned fully counter-clockwise (to the minimum)?
■ Have any or all of the Elements’ Insertion Effect Output parameters been set to “thru” in the effect setting display in the Voice Edit
mode?
■ Have any or all of the effect types been set to “thru” or “off”?
■ When this occurs in the Performance mode/Song mode/Pattern mode, check whether the Insertion Switch (INS SW) parameters
are set properly or not.
The Edit Indicator appears, even when parameters are not being edited.
■ Keep in mind that even though the Edit mode is not active, simply moving a Knob/Slider or playing back the Song/Patter n
changes the current Voice, Performance, or Mixing, causing the Edit Indicator to appear.
Cannot start the Arpeggio.
■ Check whether the [ARPEGGIO ON/OFF] button is turned on or off.
■ Is the MIDI Sync parameter set to internal (using internal clock)?
■ When the User Arpeggio type is selected, does the currently selected Arpeggio actually contain data?
■ Are the Arpeggio related parameters such as Note Limit and Velocity Limit set appropriately?
[VOICE]
→
[F2] Porta
→
Mono/Poly Mode (page 93)
[PERFORM]
→
[EDIT]
→
Part selection
→
[F1] Voice
→
[SF1] Voice
→
Mono/Poly (page 152)
[SONG]/[PATTERN]
→
[MIXING]
→
[EDIT]
→
Part selection
→
[F1] Voice
→
[SF1] Voice
→
Mono/Poly (page 235)
[UTILITY]
→
[F1] General
→
[SF1] Play
→
Tune (page 259)
[UTILITY]
→
[F1] General
→
[SF1] Play
→
Note Shift (page 259)
[VOICE]
→
[EDIT]
→
[COMMON EDIT]
→
[F1] General
→
[SF2] Play Mode
→
Bank, Tuning Number, Tuning Root (page 99)
[VOICE]
→
[EDIT]
→
Element/Key selection
→
[F5] Elm LFO
→
P Mod (page 125)
[PERFORM]
→
[EDIT]
→
Part selection
→
[F1] Voice
→
[SF1] Voice (page 151)
[SONG]/[PATTERN]
→
[MIXING]
→
[EDIT]
→
Part selection
→
[F1] Voice
→
[SF1] Voice (page 235)
[SONG]/[PATTERN]
→
[F2] Play FX
→
Note Shift (page 184)
[VOICE]
→
[EDIT]
→
[COMMON EDIT]
→
[F6] Effect
→
[SF1] Connect
→
Element Out 1-8 (page 108)
[PERFORM]
→
[EDIT]
→
[COMMON EDIT]
→
[F5] Effect
→
[SF2] InsSwitch (page 150)
[PERFORM]
→
[EDIT]
→
Part selection
→
[F1] Voice
→
[SF1] Voice (page 151)
[SONG]/[PATTERN]
→
[MIXING]
→
[F1] Part 1-16
→
Ins FX Sw (page 232)
[SONG]/[PATTERN]
→
[MIXING]
→
[COMMON EDIT]
→
[F5] Effect
→
[SF2] Ins Switch (page 234)
[UTILITY]
→
[F5] Control
→
[SF2] MIDI
→
MIDI Sync = internal (page 268)
[VOICE]
→
[EDIT]
→
[COMMON EDIT]
→
[F2] ARP Main (page 101)
[PERFORM]
→
[EDIT]
→
Part selection
→
[F2] ARP Main (page 154)
[SONG]/[PATTERN]
→
[MIXING]
→
[EDIT]
→
Part selection
→
[F2] ARP Main (page 235)