Yamaha MOTIF XS7 EN - Manual (Page 263)

System Settings (Utility mode, etc.)
MOTIF XS Owner’s Manual 263
V
oice mode
Song mode
P
attern mode
Mixing mode
Master mode
Utility mode
File mode
P
erf
ormance mode
Sampling
mode 1
Sampling
mode 2
Ref
erence
3 [SF5] Select
Pressing this button calls up the Select Auto Load File
display. From this display you can specify the file (in the
external storage device) to be loaded automatically when
turning the power on (when Auto Load is set to on).
From this display you can specify the file (in the external
storage device) to be loaded automatically when tur ning the
power on (when Auto Load is set to on). Move the cursor to
the desired file then press the [ENTER] button to determine
the Auto Load File.
Parameters 1 – 4 are the same as the ones in the File
window (page 275) of the File mode.
Audio In/Out Settings—[F2] I/O
(Input/Output)
From this display you can set Audio In/Out parameters.
1 Mic/Line
When using the A/D INPUT jacks, this determines the input
source, microphone (mic) or line.
Settings: mic, line
mic
Intended for low output equipment, such as a microphone, electric
guitar or bass.
line
Intended for high output equipment, such as a keyboard, synthesizer,
or CD player.
2 L&R Gain
Determines the output gain of the OUTPUT L/MONO and R
jacks.
Settings: 0dB, +6dB
3 Assign L&R Gain
Determines the output gain of the ASSIGNABLE OUTPUT L
and R jacks.
Settings: 0dB, +6dB
4 – ) mLAN Gain
Determines the output gain of the mLAN connector.
Settings: 0dB, +6dB
! mLAN Monitor Setup
Determines the audio signal flow for monitoring the sound
when using the MOTIF XS with DAW software installed on a
computer connected to the MOTIF XS via an IEEE1394
cable.
n You will need to properly set up the DAW software in addition
to making the settings here. For details, see page 47.
Settings: stand alone, with PC, with PC (DirectMonitor)
stand alone
This should be selected when you are using the MOTIF XS alone or are
not using the DAW software even with a computer connected to the
MOTIF XS via an IEEE1394 cable. When this is selected, the audio
signal of the MOTIF XS will be output directly via the OUTPUT L/MONO
and R jacks normally.
with PC
This should be selected when you are using the MOTIF XS as an audio
device with the DAW software. When this is selected, the audio signal
of the MOTIF XS will be output to the DAW software on a computer via
an IEEE1394 cable, merged and mixed with the DAW sound, returned
back to the MOTIF XS, then output via the OUTPUT L/MONO and R
jacks. Selecting this allows you to apply VST Effects within the DAW
software to the MOTIF XS sound.
with PC (DirectMonitor)
This should be selected when recording your keyboard performance to
the DAW software on the computer. The audio signal of the MOTIF XS
will be output directly via the OUTPUT L/MONO and R jacks with the
audio signal sent from the DAW software via an IEEE1394 cable. Keep
in mind that the Rec Monitor of the DAW software should be set to “off”
in order to prevent “double” sound from occurring.
n When “with PC” is selected, there may be a short delay
between when you play the keyboard and when you hear the
resulting sound.
n Set this parameter to “stand alone” when the MOTIF XS is not
connected to an external device via an IEEE1394 cable.
System Settings for the Voice
mode—[F3] Voice
From the following displays, you can set parameters
related to the Master Effect, Master EQ, Audio Input part,
Controller, and Micro Tuning in the Voice mode. These
settings will be applied to all Voices. The following displays
are available only when entering the Utility mode from the
Voice mode.
Specifying the Auto Load File
[SF4]
➞ [SF5] Select
1
2
3
4
Upper Level
Directory
1
!
2
3
4
5
6
7
8
9
)