Yamaha RX-V1900BL - Manual (Page 83)

79
En
Customizing this unit (MANUAL SETUP)
AD
V
ANCED
OPERA
T
ION
English
Parametric equalizer select PEQ SELECT
Use this feature to select the parametric equalizer type that
applied to the results of the automatic setup.
“PEQ SELECT” is available only when “EQ TYPE” is set to
“AUTO PEQ”.
■ Low-frequency effect level
B)LFE LEVEL
Use this feature to adjust the output level of the LFE (low-
frequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective when the input
signal contains the LFE channel.
Control range: –20 to 0 dB
Control step: 1 dB
Speakers SPEAKER
Adjusts the speaker LFE level.
Headphones HEADPHONE
Adjusts the headphone LFE level.
Depending on the “LFE/BASS OUT” setting (page 75), some
signals may not be output at the SUBWOOFER PRE OUT jack.
■ Dynamic range
C)DYNAMIC RANGE
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding bitstream signals.
Speakers SPEAKER
Adjusts the dynamic range compression for the speakers.
Headphones HEADPHONE
Adjusts the dynamic range compression for the
headphones.
■ Audio and video synchronization
(lip sync) D)LIPSYNC
HDMI automatic lip sync mode HDMI AUTO
If the connected video monitor is connected to the HDMI
OUT jack of this unit and compatible with the automatic
audio and video synchronization function (automatic lip
sync), this unit adjusts the audio and video
synchronization automatically. Use this feature to activate
or deactivate the automatic lip sync.
Auto delay AUTO DELAY
Use this feature to make fine adjustments of the audio and
video synchronization when you set “HDMI AUTO” to
“ON”.
Control range: 0 to 240 ms
Control step: 1 ms
y
“offset” indicates the difference between the value of the audio
delay that this unit sets automatically and the value of the audio
delay that you set in “AUTO”. This unit stores the value of
“offset” and applies the value to other automatic lip sync
compatible video monitors.
Manual delay MANUAL DELAY
Use this feature to adjust the delay of the sound output
manually to synchronize audio with video images when
you set “HDMI AUTO” to “OFF”.
Control range: 0 to 240 ms
Control step: 1 ms
Choice Functions
NATURAL Averages out the frequency response of each all
speakers with higher frequencies being less
emphasized. Recommended if the “FLAT”
setting sounds a little harsh.
FLAT Averages frequency response of all speakers.
Recommended if all of your speakers are of
similar quality.
FRONT Adjusts the frequency response of each speaker
in accordance with the sound of your front
speakers. Recommended if your front speakers
are of much higher quality than your other
speakers.
Note
Note
Choice Functions
MIN/AUTO • MIN: Adjusts the dynamic range to narrow
when this unit is decoding bitstream signals
(except Dolby TrueHD).
• AUTO: Adjusts the dynamic range according
to the instruction of the input source signals
when this unit is decoding Dolby TrueHD
signals.
STD Adjusts the dynamic range to medium. When
this unit is decoding Dolby TrueHD signals, the
dynamic range control is always active
regardless of the instruction of the input source
signals.
MAX Preserves the greatest amount of dynamic range.
Choice Functions
OFF Select this setting if the video monitor is not
compatible with the automatic lip sync or you do
not want to use the automatic lip sync. Use
“MANUAL DELAY” to adjustment the audio
and video synchronization.
ON Select this setting if the connected video monitor
is compatible with the automatic lip sync. Use
“AUTO DELAY” to make fine adjustments of
the audio and video synchronization.