GW Instek GDS-122 User Manual - Manual (Page 49)

Specifications
97
S
PECIFICATIONS
Conditions for
specifications
The following specifications are applicable when
these two conditions are met:
• The GDS‐122 has been powered up for at least
30 minutes, during which temperature
fluctuation is no more than 5 degrees Celsius.
• The probe attenuation is set to X 10.
69B
Oscilloscope specifications
Sampling Mode Normal, Peak detection, Average
Rate 100 MSa/s
Input Coupling DC, AC
Impedance 1MΩ±2% in parallel with 20pF±3pF
Probe 1X, 10X, 100X, 1000X
Max. Input 400V (peak)
Channel delay 150ps (typical)
Horizontal Sampling rate 10S/s～100mS/s
Interpolation （ sin x）/x
Record length 6K points on each channel
Scanning speed 5ns/div～5s/div, 1-2.5-5 step
Sampling rate /
relay time accuracy ± 100ppm (time interval ≥ 1ms)
Interval (△T)
accuracy (full
bandwidth) Single: ±(1 interval time +100ppm×
reading+0.6ns) Average >16 : ±(1
interval time +100ppm×reading+0.4ns)
Vertical A/D converter 8 bits resolution (2CH simultaneously)
Sensitivity 5mV/div～5V/div（at input）
Displacement ± 50V(500mV～5V),±1V(5mV～200mV)
Bandwidth 20M
Single Full bandwidth
Low frequency ≥5Hz（at input, AD coupling, -3dB）
Rise time ≤17.5ns (at input, typical)
DC accuracy ± 5% (DC gain)
DC accuracy (avg) Avg >16: ±(5% rdg + 0.05 div) for △V
GDS-122 User Manual
98
Trigger Sensitivity CH1 and CH2: 1div(DC～full bandwidth)
DC coupling: ≥ 50Hz.
Trigger level ± 6 divisions from the screen center
Level accuracy ± 0.3 div (typical, rise/fall time ≥ 20ns)
Displacement 655div (pre-trigger), 4div (post- trigger)
50% level setting Input signal frequency ≥ 50Hz (typical)
Trigger sensitivity 2 div of peak-to-peak (video trigger)
Signal system NTSC, PAL, SECAM (any frequency)
Measurement Cursor △ V and △T between cursors
Automatic Peak-to-peak, average, root mean
square, frequency, and cycle
Probe 1X position 10X position
Bandwidth ≤ 6 MHz (DC) Full bandwidth (DC)
Attenuation rate 1: 1 10: 1
Compensation 10pf～35pf 10pf～35pf
Input impedance 1MΩ±2％ 10MΩ±2％
Input impendence 85pf～115pf 14.5pf～17.5pf
Input voltage 150 V DC 300V DC
70B
Multimeter specifications
VDC Input impedance 10MΩ
Max input 1000V (DC or AC peak-to-peak value)
Accuracy ± 1%±1 digit
Resolution 400mV range: 100uV
4V range: 1mV
40V range: 10mV
400V range: 100mV
VAC Input impedance 10MΩ
Max input 750V(AC, virtual value)
Frequency range 40Hz~400Hz
Display Virtual value of sine wave
Accuracy ± 1%±3 digits
Resolution 4V range: 1mV
40V range: 10mV
400V range: 100mV
DCA Accuracy 40mA range: ±1%±1 digit
400mA range: ±1.5%±1 digit
20A range: ±3%±3 digits
Resolution 40mA range: 10uA