Kontron AT8050 User Manual
Kontron user's guide, At8050
Advertising
Table of contents
Document Outline
- Table of Contents
- List of Figures
- List of Tables
- Safety Instructions
- Preface
- 1. Product Description
- 2. Board Features
- 2.1 Block Diagram
- 2.2 System Core
- 2.3 USB 2.0 Interfaces
- 2.4 USB Flash Module
- 2.5 Serial ATA/Serial Attached SCSI
- 2.6 Update Channel
- 2.7 Real Time Clock & NVRAM
- 2.8 Redundant BIOS Flash
- 2.9 Ethernet Interfaces
- 2.9.1 Fabric Interface
- 2.9.2 Base Interface
- 2.9.3 Management Interface
- 2.9.4 Ethernet Interfaces Configuration
- 2.9.4.1 10GbE and Management to Front Panel Configuration
- 2.9.4.2 10GbE and Management to AMC Configuration
- 2.9.4.3 10GbE and Management to RTM Configuration
- 2.9.4.4 AMC to Fabric Interface and Management to Front Panel Configuration
- 2.9.4.5 AMC to Fabric Interface and Management to AMC Configuration
- 2.9.4.6 AMC to Fabric Interface and Management to RTM Configuration
- 2.9.4.7 Management to Fabric Interface Configuration
- 2.10 Serial Interfaces
- 2.11 AMC Mezzanine
- 2.12 FPGA
- 2.13 Telecom Clock Option
- 2.14 Redundant IPMC Firmware & BootBlock
- 2.15 LEDs Description
- 3. Installing the Board
- 4. Hardware Management
- 5. Software Setup
- 5.1 AMI BIOS Setup Program
- 5.1.1 Accessing the BIOS Setup Utility
- 5.1.2 Menu Bar
- 5.1.3 Main Menu
- 5.1.4 Advanced Menu
- 5.1.4.1 Advanced Processor Configuration sub-menu
- 5.1.4.2 ACPI Configuration sub-menu
- 5.1.4.3 Drive Configuration sub-menu
- 5.1.4.4 Event Log Configuration sub-menu
- 5.1.4.5 Expansion ROM Configuration sub-menu
- 5.1.4.6 PCI Express Configuration sub-menu
- 5.1.4.7 USB Configuration sub-menu
- 5.1.4.8 USB Mass Storage Device Configuration sub-menu
- 5.1.4.9 Advanced Chipset Control sub-menu
- 5.1.4.10 Intel VT-d Configuration Sub-Menu
- 5.1.4.11 I/O Virtualization Sub-Menu
- 5.1.5 Security Menu
- 5.1.6 Boot Menu
- 5.1.7 System Management Menu
- 5.1.7.1 Remote Access Configuration sub-menu
- 5.1.7.2 Set LAN Configuration sub-menu
- 5.1.7.3 IP Configuration sub-menu
- 5.1.7.4 MAC Address Configuration sub-menu
- 5.1.7.5 Subnet Mask Configuration sub-menu
- 5.1.7.6 Gateway Address Configuration sub-menu
- 5.1.7.7 VLAN ID Configuration
- 5.1.7.8 VLAN Priority Configuration
- 5.1.7.9 Watchdog Timer sub-menu
- 5.1.7.10 System Information sub-menu
- 5.1.7.11 IPMI Device and FW Info sub-menu
- 5.1.7.12 OEM e-keying Configuration sub-menu
- 5.1.7.13 Managed FRU Deactivation Policies sub-menu
- 5.1.8 Exit Menu
- 5.2 Boot Utilities
- 5.3 Console Redirection (VT100 Mode)
- 5.1 AMI BIOS Setup Program
- 6. Thermal Considerations
- A. Memory & I/O Maps
- A.1 Memory Mapping
- A.2 Kontron I/O Mapping
- A.3 PCI IDSEL and Device Numbers
- A.4 Telco Clock
- A.4.1 Register Description
- A.4.1.1 Base + 00h TelClock0: Backplane Clock Status, PLL Reference & Interface Selection
- A.4.1.2 Base + 01h TelClock1: PLL Control & Status
- A.4.1.3 Base + 02h TelClock2: AMCs Clock Enables & Frequency Selection
- A.4.1.4 Base + 03h TelClock3: PLD Configuration & Version
- A.4.1.5 Base + 04h TelClock4: Backplane CLK3A/B configuration (optional)
- A.4.1.6 Base + 05h TelClock5: Clock Events & Alarm (IPMC only)
- A.4.1 Register Description
- B. Connector Pinouts
- C. BIOS Setup Error Codes
- D. Software Update
- E. Getting Help
- F. Glossary