Rice Lake IQ plus 2100SL Digital Bench Scale - Manual (Page 36)

Appendix 25
6.0 Appendix
6.1 Error Messages
The IQ plus 210 indicator provides a number of error messages. When an error occurs, the message is shown on the
indicator LED display. Error conditions can also be checked remotely by using the XE EDP command as described
in Section 6.1.2.
6.1.1 Displayed Error Messages
The IQ plus 210 provides a number of front panel error
messages to assist in problem diagnosis. Table 6-1 lists
these messages and their meanings.
6.1.2 Using the XE EDP Command
The XE EDP command can be used to remotely query
the IQ plus 210 for the error conditions sho wn on the
front panel. The XE command returns tw o 5-digit
numbers in the format:
xxxxx yyyyy
where
xxxxx
contains a decimal representation of an y
existing error conditions as described in Table 6-2.
If more than one error condition e xists, the number
returned is the sum of the v alues representing the error
conditions. For example, if the XE command returns
the number 528, this v alue represents the sum of an
A/D physical error (512) and an A/D calibration
checksum error (16).
The second number returned (
yyyyy
) uses the same bit
assignments as shown in Table 6-2 to indicate whether
the test for the error condition w as run. For example,
the value
yyyyy
= 51807 represents the decimal
equivalent of the binary v alue 1100 1110 0111 1111.
Using the bit assignments in T able 6-2, this v alue
indicates all tests were run.
Error Message Description Solution
E A/D A/D physical error Call Rice Lake Weighing Systems (RLWS) Service.
EEEROM EEPROM physical error
EVIREE Virgin EEPROM Use the DEFLT menu to restore defaults, then recalibrate load cells.
EPCKSM Parameter checksum error
EACKSM A/D calibration checksum error A/D converter requires recalibration. Call RLWS Service.
ELCKSM Load cell calibration checksum error Recalibrate load cells.
EIDATA Internal RAM checksum error Call RLWS Service.
INOVFL Internal overflow error Remove weight from scale. If error recurs, check configuration, check
scale for damage.
OVERFL Overflow error Weight value too large to be displayed.
- - - - - - Gross > overload limit Gross value exceeds overload limit. Check configuration.
_ _ _ _ _ _ A/D underrange A/D reading < –4 mV. Check scale for binding or damage.
Table 6-1. IQ plus 210 Error Messages
Error
Code Description Binary Value
0 No error 0000 0000 0000 0000
1 EEPROM physical error 0000 0000 0000 0001
2 Virgin EEPROM 0000 0000 0000 0010
4 Parameter checksum error 0000 0000 0000 0100
8 Load cell calibration
checksum error 0000 0000 0000 1000
16 A/D calibration checksum
error 0000 0000 0001 0000
32 not assigned 0000 0000 0010 0000
64 Internal RAM checksum error 0000 0000 0100 0000
128 not assigned 0000 0000 1000 0000
256 not assigned 0000 0001 0000 0000
512 A/D physical error 0000 0010 0000 0000
1024 not assigned 0000 0100 0000 0000
2048 Internal overflow error 0000 1000 0000 0000
4096 not assigned 0001 0000 0000 0000
8192 not assigned 0010 0000 0000 0000
16384 A/D underrange 0100 0000 0000 0000
32768 Gross > overload limit 1000 0000 0000 0000
Table 6-2. Error Codes Returned on XE Command