Atlona AT UHD CLSO 824 - Manual (Page 25)

25
atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Command Feedback Description
EDIDMSetX default
Ex. EDIDMSet3 default EDIDMSetX default
Ex. EDIDMSet2 default Sets the input EDID to default X=Input
Ex. Set input 2 EDID to default
EDIDMSetX saveY
Ex. EDIDMSet7 save2 EDIDMSetX saveY
Ex. EDIDMSet7 save2 Set input X EDID to the saved EDID memory (Y)
Ex. Set input 7 to the EDID saved to memory 2
EDIDMSetX intZ
Ex. EDIDMSet3 int7 EDIDMSetX intZ
Ex. EDIDMSet3 int7 Set input EDID to the chosen internal EDID (Z)
Ex. Set input 3 to the internal EDID 7
EDIDMSetX sta
Ex. EDIDMSet6 sta EDIDMSetX sta
Ex. EDIDMSet6 default Displays the current EDID (Y) of the selected input (X)
Ex. Input 6 is set to default EDID
EDIDOutX memY
Ex. EDIDOut2 mem1 EDIDOutX memY
Ex. EDIDOut2 mem1 Copies EDID from an output (x) to a chosen memory location (y)
Ex. Sets output 2 EDID to EDID memory 1
PrefTimg8 Y
Ex. PrefTimg8 3 PrefTimg8 Y
Ex. PrefTimg8 3 Set the preferred timing of the VGA port Y=0-7
Ex. Set the VGA port to 1024x768
PrefTimg sta PrefTimg8 Y Displays the preferred timing for the VGA port
List X
Ex. List Pref List X
Ex. Pref 0: Default
Pref 1 : 1280x800
etc Displays the preferred timings (Pref) and EDIDs (EDID) available
HDCPSetX Y
Ex. HDCPSet5 Off HDCPSetX Y
Ex. HDCPSet5 Off Sets HDCP reporting mode of the HDMI input port Y=on,off,sta
Ex. Set input 5 to HDCP non-compliant
Internal EDIDs -
01 2160P60 Multi CH
02 2160P60 2CH 03 2160P30 Multi CH
04 2160P30 2CH 05 1920x1200 RGB 2CH 06 1080P DD
07 1080P Multi CH 08 1080P 2CH 09 1080P 3D DD
10 1080P 3D Multi CH 11 1080P 3D 2CH 12 1080P DVI
13 1280x800 RGB 2CH 14 1280x800 RGB DVI 15 1366x768 RGB 2CH
16 1024x768 RGB 2CH 17 720P DD
18 720P 2CH
19 800x600 RGB 2CH
Prefered Timings -
00 Default
01 1920x1200 02 1920x1080
03 1280x800 04 1366x768 05 1024x768
06 1280x720 07 800x600
RS-232 Command for the Output baud rate status
RS232para
The RS-232 status command will provide feedback for the current parameters for each transmitter/
receiver.
Example: (See example of feedback below)
RS232para
Current RS232 parameters:
- Zone 1-15 :BaudRate 2400bps, DataBits 0, Parity None, StopBits 1.
Note: Zone 1-10 are the captive screw connectors, Zones 11-13 are the HDBaseT inputs, and Zones 14-15 are the
HDBaseT outputs.
Note: Default for the transmitters/receivers is: Baud-9600bps, Data length-8bit, Parity-None, Stop Bit-1