Chapter 4 – DFI HU968 User Manual
Page 33
www.dfi .com
Chapter 4 BIOS Setup
33
Chapter 4
CPU Configuration
This section is used to configure the CPU. It will also display the detection of CPU information.
Active Processor Cores
Select the number of cores in each processor package.
Limit CPUID Maximum
The CPUID instruction of some newer CPUs will return a value greater than 3. The
default is Disabled because this problem does not exist in the Windows series operat-
ing systems. If you are using an operating system other than Windows, this problem
may occur. To avoid this problem, enable this field to limit the return value to 3 or less
than 3
.
Intel Virtualization Technology
When this field is set to Enabled, the VMM can utilize the additional hardware capabili-
ties provided by Vanderpool Technology.
EIST
This field is used to enable or disable the Intel Enhanced SpeedStep Technology.
Number of cores to enable
in each processor package.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Advanced
Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous
Values
F3: Optimized
Defaults
F4: Save & Reset
ESC: Exit
CPU Confi guration
Intel(R) Celeron(R) 2980U @ 1.60GHz
CPU Signature
Microcode Patch
Max CPU Speed
Min CPU Speed
CPU Speed
Processor Cores
Intel HT Technology
Intel VT-X Technology
Intel SMX Technology
64-bit
EIST Technology
CPU C3 State
CPU C6 State
CPU C7 State
L1 Data Cache
L1 Code Cache
L2 Cache
L3 Cache
Active Processor Cores
Limit CPUID Maximum
Intel Virtualization Technology
EIST
40651
8
1600 MHz
800 MHz
1600 MHz
2
Not Supported
Supported
Not Supported
Supported
Supported
Supported
Supported
Supported
32 KB x2
32 KB x2
256 KB x2
2048 KB
[All]
[Disabled]
[Enabled]
[Disabled]
SATA Configuration
This section is used to configure settings of SATA devices.
Enable or disable SATA
Device.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
SATA Controller(s)
SATA Mode Selection
Serial ATA Port 0
Software Preserve
Port 0
SATA Device Type
Serial ATA Port 1
Software Preserve
Port 1
SATA Device Type
Serial ATA Port 2
Software Preserve
Port 2
SATA Device Type
Advanced
SATA Controller(s)
This field is used to enable or disable the Serial ATA device.
SATA Mode Selection
Determine how the Serial ATA controller(s) operates.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller
Interface.)
RAID Mode
This option allows the Serial ATA devices to use RAID 0/1/5/10/Recovery (Redundant
Array of Independent Disks.)
Port 0/1/2
Enable or disable the Serial ATA port.
SATA Device Type
Identify the Serial ATA port which is connected to the Solid State Drive or the Hard
Disk Drive.
[Enabled]
[AHCI]
Empty
Unknown
[Enabled]
[Hard Disk Drive]
Empty
Unknown
[Enabled]
[Hard Disk Drive]
4GB NANDrive (3.9GB)
SUPPORTED
[Enabled]
[Hard Disk Drive]
Select Screen
Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous
Values
F3: Optimized
Defaults
F4: Save & Reset
ESC: Exit