Document Outline

• Preface
  • Conventions used in this document
  • Safety terms and symbols
• Chapter 1 Introduction
  • Product overview
    • Product contents
  • System requirements
    • Operational requirements
      • Figure 1. Typical DVR system
      • Figure 2. Typical IP system
      • Figure 3. Typical enhanced system
    • Minimum load requirements
      • Table 1. Minimum load requirements of dome configurations
    • Power requirements
      • Table 2. Power requirements at 24 VAC (±4 VAC) operating voltage
    • Cable management
      • Figure 4. Three acceptable typical cabling scenarios
    • Cable requirements
      • Table 3. Cable requirements
    • Power cable size and length requirements
      • Table 4. Recommended power cable gauges based on maximum lengths for an operating voltage of 24 VAC (±4 VAC)
• Chapter 2 Housings and cables
  • Backward compatibility with CyberDome I housings
  • Various mounting and housing styles
    • Figure 5. Basic mounting styles
    • Figure 6. Basic housing styles
  • Wiring best practices
    • Pendant-mount wire routing
      • Figure 7. Side view of pendant-mount cabling and typical wall-mount
      • Figure 8. Top view of pendant-mount cabling
    • Flush-mount wire routing
      • Figure 9. Side view of flush-mount cabling
      • Figure 10. Top view of flush-mount cabling
  • Pendant-mount housings
    • Preparing the surface for pendant-mounts
    • Installing the housing
      • Figure 11. Installing the pendant-mount housing
  • Flush-mount housings
    • Preparing the surface for flush-mounts
      • Figure 12. Preparing the mounting surface for flush-mount housings being mounted into solid surfaces not requiring reinforcement
    • Installing the housing
      • Figure 13. Installing the flush-mount housing
  • Fan installation
    • Figure 14. Installing the new fan on the PTZ unit
    • Figure 15. Connecting the new fan cable
  • Preparing the cables
    • Figure 16. Prepared cables
• Chapter 3 Wiring
  • Components used for basic and advanced operation
    • Figure 17. Housing board
    • Table 5. Cyberdome II housing interface board UTC LED functions
    • Alarm/contact connectors
      • Figure 18. Data and alarm/contact connectors
  • Wiring the housing board
    • Figure 19. Data connections
    • Figure 20. Video connection
    • Figure 21. Power connection
  • Setting the termination
    • Figure 22. Termination switches
• Chapter 4 Camera assembly, shroud, dome
  • Camera assembly preparation and installation
    • Figure 23. Protocol and site address DIP switch blocks
    • Setting the protocol
      • Table 6. Protocols
    • Setting the camera’s address
      • Table 7. Dip switch positions and equivalent values
      • Figure 24. Address DIP switches (set to 210: 128 + 64 + 16 + 2)
      • Table 8. Address DIP switch settings for cameras 1 to 64
    • Installing the camera assembly
      • Figure 25. Installing the pan/tilt assembly
  • Shroud and bubble dome installation
    • Installing a camera shroud
      • Figure 26. Camera shroud installation
    • Installing a dome
      • Figure 27. Attaching the dome to the housing (cameras not shown to show safety clips clearly)
• Chapter 5 Troubleshooting, maintenance, support
  • Troubleshooting
    • Figure 28. Housing board power indication
  • Maintenance
    • Cleaning the dome
  • Contacting us
    • Table 9. Technical support
    • Online resources
• Appendix A Mount kits
  • GEA-102 wall-mount arm
    • Installing the wall-mount arm
      • Figure 29. Leaving the safety chain tied
      • Figure 30. Removing the access cover
      • Figure 31. Marking the mounting and cable entry holes
      • Figure 32. Fastening the arm to the mounting surface
      • Figure 33. Reattaching the access cover
      • Figure 34. Attaching the housing safety cable to the arm safety chain
    • Opening a conduit hole
      • Figure 35. Opening a conduit hole
  • GEA-114 T-bar ceiling support kit
    • Figure 36. Parts of a supported T-bar ceiling
    • Installing the T-bar ceiling support kit
      • Figure 37. Aligning the angle brackets and ceiling ring on the panel
      • Figure 38. Marking the mounting holes and housing pass-through hole
      • Figure 39. Fastening the support kit onto the removable ceiling panel
      • Figure 40. Installed T-bar support kit
• Appendix B Protocol functionality
  • CyberDome II protocol functionality
    • Table 10. Pelco D and P commands supported
    • Table 11. Ultrak commands supported
    • Table 12. VCL commands supported
    • Table 13. Vicon commands supported
    • Table 14. AD RS-422 commands supported
    • Table 15. Panasonic commands supported
    • Table 16. Bosch RS-232 commands supported
    • Table 17. KD6 commands supported
  • Equipment protocol testing list
    • Table 18. Keypads used for testing protocols
• Index