Marantz BD8002 - Manual (Page 15)

12
Connections
ENGLISH
Connections
ENGLISH
* 1 If “BD Audio Mode” is set to “Mix Audio Output” audio will be output as Multi LPCM. Refer to page 23.
* 2 Outputs audio signals decoded from independent substream.
* 3 For DTS-HD Master Audio, outputs audio signals decoded from DTS-HD Master Audio stream, and
for DTS-HD High Resolution Audio, outputs audio signals decoded from DTS core stream.
• If the connected device is not compatible with the HDMI BITSTREAM, audio will be output as Multi
LPCM or 2ch Downmix LPCM depends on the capability of the connected device even if you select
“HDMI Multi(Normal)” in“HDMI Audio Out” setting. Refer to page 32.
* HDMI: High-Definition Multimedia Interface
Ⅵ Audio signals output from DIGITAL OUT
When both HDMI and DIGITAL OUT is connected to other devices, the audio signals currently output from
the HDMI OUT will be output from the DIGITAL OUT jack as well, except that Dolby Digital signal will be
output instead of Dolby Digital Plus and Dolby TrueHD, and DTS signal will be output instead of DTS-HD.
< When HDMI is not connected or “Audio Mute” is selected···>
When HDMI is not connected or the “Audio Mute” is selected in “HDMI Audio Out” setting, the audio signals
output from DIGITAL OUT changes depending on the “Digital Out” setting. Refer to the following table.
To set “Digital Out”, press [SETUP], then select “Quick”
A “HDMI Audio Out” A “Audio Mute” or
“Custom” A “Audio” A “HDMI Audio Out” A “Audio Mute”.
* 1 For the BD title with secondary or interactive audio, these audio will be output as Dolby Digital
when all the conditions listed below are met:
• When “BD Audio Mode” is set to “Mix Audio Output”.
• When “HDMI Audio Out” is set to “Audio Mute”.
• When “Digital Out” is set to “Bitstream”.
If the BD title does not have secondary or interactive audio, the audio will be output as shown in the table.
• This table applies only when HDMI is not connected or the “Audio Mute” is selected in “HDMI Audio
Out” setting.
Copyright protection system
To play back the digital video images of a BD/DVD via an HDMI connection, it is necessary that both
the unit and the display device (or an AV amplifier) support a copyright protection system called
HDCP (high-bandwidth digital content protection system). HDCP is copy protection technology that
comprises data encryption and authentication of the connected AV device. This unit supports HDCP.
Please read the operating instructions of your display device (or AV amplifier) for more information.
Note
• When using HDCP-incompatible display device, the image will not be viewed properly.
• Among the devices that support HDMI, some devices can control other devices via the HDMI
jack, this unit cannot be controlled by another device via the HDMI jack.
• The audio signals from the HDMI jack (including the sampling frequency, the number of
channels and bit length) maybe limited by the device that is connected.
• Among the monitors that support HDMI, some do not support audio output (e.g, projectors). In
connections with device such as this unit, audio signals are not output from the HDMI output jack.
Digital Connection to an AV Amplifier with Built-in Decoder
COAXIAL DIGITAL AUDIO INPUT OPTICAL DIGITAL AUDIO INPUT
audio
this unit
or
digital audio coaxial/
optical cable
digital audio coaxial/
optical input jack
Disc type Audio recording format “Digital Out” setting
Bitstream LPCM
BD-video
Dolby Digital Dolby Digital 2ch Downmix LPCM
Dolby Digital Plus Dolby Digital 2ch Downmix LPCM
Dolby TrueHD Dolby Digital 2ch Downmix LPCM
DTS DTS* 1 2ch Downmix LPCM
DTS-HD DTS* 1 2ch Downmix LPCM
LPCM 2ch Downmix LPCM* 1 2ch Downmix LPCM
BD-RE/BD-R
AAC AAC 2ch Downmix LPCM
LPCM 2ch Downmix LPCM 2ch Downmix LPCM
DVD-video
Dolby Digital Dolby Digital 2ch Downmix LPCM
DTS DTS 2ch Downmix LPCM
LPCM 2ch Downmix LPCM 2ch Downmix LPCM
DivX ®
Dolby Digital Dolby Digital 2ch Downmix LPCM
MP3/MP2 2ch LPCM 2ch LPCM
audio CD/ MP3/Windows Media™ Audio 2ch LPCM 2ch LPCM
DTS-CD DTS 2ch Downmix LPCM
Note
• In order to output LPCM signal from DIGITAL OUT jack while outputting the HDMI audio signal,
set “BD Audio Mode” to “Mix Audio Output” and set “HDMI Audio Out” to “HDMI Multi(LPCM)”.
Note for Optical Cable
• Optical cable may be damaged when bent at sharp angles. Ensure cables are coiled in loops with
a diameter of 6 inches (15cm) or more when storing them.
• Use a cable which is 9.8 feet (3m) or shorter.
• Insert cable plugs firmly into the jacks when making connections.
• If a plug has dust or is dirty, clean it with a soft cloth before inserting it into a jack.
Cables not included.
Please purchase the necessary cables at your local store.
E5E30UD_EN.book Page 12 Thursday, May 22, 2008 3:43 PM