Marantz BD8002 - Manual (Page 41)

38
Others
ENGLISH
ENGLISH
Others
If the unit does not perform properly when operated as instructed in this Operating Instruction, check the unit, consulting the following checklist.
Troubleshooting
Problem Solution Page
No power - Check if the AC cord is properly connected.
- Unplug the AC cord once, and wait for 5-10 seconds and then plug it
in again.
–
–
No sound or picture - Check if the connected display device is turned on.
- Check the HDMI connection. (Check the status of the HDMI related
indications.)
- Check the RCA audio/video cable connections.
- Check if the pure direct mode is set to “Video Off” or “All Off”. If it is
the case, set it to “Display Off” or “Normal”.
- Check whether the connected display device or other device supports
HDCP. (This unit will not output a video signal unless the other device
supports HDCP.)
- Check whether the output format of this unit (HDMI FORMAT)
matches the supported input format of other connected device.
- Check if the “HDMI Deep Color” is set to “Auto”. If it is the case, set it to
“Off”.
- Check if the “I/P Direct” is set to “On”. If it is the case, set it to “Off”.
–
10
10, 13
23
12
10,30,31
31
31
Distorted picture - Sometimes a small amount of picture distortion may appear.
This is not a malfunction.
- Connect this unit directly to the TV. If the RCA audio/video cables are
connected to a VCR, pictures may be distorted due to the copy
protection system.
–
10
Completely distorted picture or
black/white picture with BD/DVD - Make sure the disc is compatible with this unit. 4
No sound or distorted sound - Adjust the volume.
- Check that the speakers are connected correctly.
- Check the HDMI connections.
- Check the “Audio” settings. –
10,12,13
10
32,33
Picture freezes momentarily during
playback - Check the disc for fingerprints/scratches and clean with a soft cloth
wiping from center to edge.
- Clean the disc.
4
4
Disc cannot be played back - Clean the disc.
- Ensure the disc label is facing up.
- Check if the disc is defective by trying another disc.
- Cancel the ratings control or change the control level.
- Insert a correct disc that can be played back on this unit. 4
14
–
36
4
SD Memory Card cannot be read. - The format of the card does not match to this unit or the card is not
compatible.
–
No return to start-up screen when
disc is removed - Reset this unit by turning it off, then on again. –
The unit does not respond to the
remote control - Aim the remote control directly at infrared sensor window on the front
of the unit.
- Reduce the distance to infrared sensor window.
- Replace the batteries in the remote control.
- Re-insert the batteries with their polarities (+/- signs) as indicated.
- Make the signal code of the remote control match to the signal code
of the unit.
6
–
6
6
6
Problem Solution Page
Buttons do not work or the unit
stops responding - To completely reset the unit, unplug the AC cord from the AC outlet
for 5-10 seconds.
–
The unit does not respond to some
operating commands during
playback - Operations may not be permitted by the disc.
Refer to the instructions of the disc.
14
The unit cannot read BD/DVD/CD - Condensation ? (Let sit 1 or 2 hours)
- You are attempting to play a disc other than one with one of the
marks on page 4.
- Wipe the dirt off the disc or replace the disc.
3
4
4
Angle does not switch - The angle cannot be switched for BD/DVD which do not contain
multiple angles. In some cases multiple angles are only recorded for
specific scenes.
19
Playback does not start when the
title is selected - Check the “Ratings” setting. 36
The password for rating level has
been forgotten - Enter the default password “4737”, then your forgotten password will
be cleared.
36
Note
• Some functions are not available in specific modes, but this is not a malfunction. Read the
description in this Operating Instructions for details on correct operations.
• Some functions are prohibited on some discs.
E5E30UD_EN.book Page 38 Thursday, May 22, 2008 3:43 PM