JVC BR-DV600AE - Manual (Page 35)

E-35
Setting
Mini
PROFESSIONAL
SET
MENIU
EJECT
REC PLAY PAUSE
REW STOP FF
DVCAM NTSC PAL REC INH.
CH-1/3
CH-2/4
BR-DV3000
A.DUB
OPERATE
INPUT SEL. REMOTE SEL. MIC
SERIAL
WIRELESS 9PIN
LINE
DV Y/C
NTSC indicator PAL indicator
INPUT SEL. switch
DIO VIDEO
LINE Y/C CH 2/4
IN
OUT
REMOTE
SERIAL 9PIN
NTSC/PAL
NTSC PAL
DC12V
NTSC/PAL switch
Rear panel
– – – A U D I O V I D E O – – –
A U D I O MO D E 4 8 K
A O U T A T S E A R C H O N
A U D I O O U T S E L C H - 1 / 2
A U D I O O U T L E V E L N O R M
S E T U P ( N T S C ) O F F
P A G E B A C K
– – – S Y S T E M [ 1 / 2 ] – – –
S T L / F . A D V 2 N D
B A C K U P R E C T I M E O F F
L O N G P A U S E T I M E 5 M I N
L O N G P A U S E MO D E F . A D V
I N D E X W R I T E O N
R E P E A T MO D E B L A N K
N E X T P A G E
P A G E B A C K
AUDIO/VIDEO menu
SYSTEM (1/2) menu
Memo
• For DV signal input, the sig-
nal system (NTSC/PAL) is
identified automatically.
• For DV signal input, the AU-
DIO MODE item cannot be
set. It will be the same mode
as that of the input signal.
(48K or 32K)
Ⅵ Setting the signal system (NTSC/PAL)
The signal system for analogue input is set with the NTSC/PAL
switch located at the rear panel. Either the NTSC or the PAL indica-
tor on the front lights up, depending on the setting.
* Before setting the NTSC/PAL switch, please set the unit to the
OPERATE OFF mode.
Ⅵ Selecting the video input signal
Please use the INPUT SEL. switch on the front panel.
Y/C : Input Y/C separate video signals.
LINE: Input composite video signals.
DV
: Input DV signals.
Ⅵ Setting the AUDIO/VIDEO menu ( ☞
Page 61)
• AUDIO MODE
Use this menu item to set the audio sampling frequency for recording.
32K : Perform recording with an audio sampling frequency of 32kHz.
Use this setting when performing audio dubbing on CH3 and
CH4.
48K : Perform recording with an audio sampling frequency of 48kHz.
Audio dubbing is not available.
• SET UP (NTSC only)
Set this item to enable/disable setup to composite signals or Y/C
separate video during recording.
Ⅵ Setting the SYSTEM menu (☞ Page 57)
• LONG PAUSE TIME
Sets the time period, after the lapse of which the unit will enter the
tape protection mode when pause is activated for an extended pe-
riod of time.
• INDEX WRITE
This setting turns on/off automatic recording of index signals when
recording begins.
Ⅵ Setting the time code recording during DV signal input
Set the TC DUPLICATE item of the TIME CODE menu to determine
whether to use the time code from the built in time code generator
and clock or the data from the DV terminal. (
☞
Page 62)
BR-DV3000_E_p03-49 06.8.24, 1:38 PM 35