Kenwood KRF-V7771D - Manual (Page 10)

10
KRF-V7771D (En/T)
System connections
Connections
Connecting system control cords lets you take advantage of convenient system control operations.
There are two types of KENWOOD system control modes. Make connections according to the groups of terminal symbols
shown below.
ƒ
Mode : lets you combine
f
,
ƒ
, and
F
terminals
Mode : for terminals only
This unit is compatible with both [XS8] and [SL16] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8] mode, follow
the instructions in “Switching from [SL16] to [XS8]” below.
[SL16] [XS8]
[SL16]
[SL16] [XS] [XS8] [XR]
[SL16] [XS] [XS8]
[XS]
[SL16] [XS8]
[SL16]
[SL16] [XS] [XS8] [XR]
[SL16] [XS] [XS8]
[XS]
SYSTEM
CONTROL
cord
SYSTEM
CONTROL
cord
Receiver
MD recorder
Cassette deck
CD player
Turntable
÷ In order to take advantage of the system control operations, the components must be connected to the correct jacks. To use a CD player it must
be connected to the CD 1 jacks. To use a cassette deck (or MD recorder) it must be connected to the MD/TAPE 1 jacks. When using more than
one CD player (etc.) only the one connected to the specified jacks may be connected for system control.
÷ Some CD players and cassette decks are not compatible with the [SL16] system control mode. Be sure to use the [XS8] system control mode
when making system connections with equipment that is not [SL16] compatible.
÷ Some MD recorders are not system-control compatible. The system control function is not available when a MD recorder is used by connecting
it through a digital input. You cannot connect the system control cord to this kind of equipment.
Notes Notes
Receiver
MD recorder
Cassette deck
CD player
Turntable
Connecting the system control
EXAMPLE: [XS8] mode connections
The underlined portion represents the setting of the system control mode.
EXAMPLE: [XS16] mode connections
The underlined portion represents the setting of the system control mode.
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system operations. If your
equipment consists of this kind of combination, please do not connect any system control cords. Even without
system control cords, normal operations can be carried out without effecting performance.
2. Do not connect system control cords to any components other than those specified by KENWOOD. It may
cause a malfunction and damage your equipment.
3. Be sure the system control plugs are inserted all the way in to the system control terminals.
System control operations
Remote Control
Lets you operate the connected components with the system
remote supplied with the receiver.
Automatic Operation (except [XR] equipment)
When you start playback from a source component, the input
selector on this unit switches to that component automati-
cally.
Synchronized Recording (except [XR] equipment)
Lets you synchronize recording with the start of playback
when recording from CD, MD or analog discs.
Switching from [SL16] to [XS8]
You can easily change the system control mode by adjusting the
position of the SYSTEM CONTROL switch on the rear panel.
Do this operation after completing all connections.
For [XS8]
÷ This operation will not effect items stored in the memory.
÷ After switching the system control mode, turn the power off and
then back on to confirm the new setting.
For [SL16]
Registering setup codes for KENWOOD audio components
÷ Once you finish making the system connections, be sure to register the appropriate setup code for each component.
÷ If you own remote controllable KENWOOD audio components that are not compatible with system control (or cannot be combined with your
other system control components), registering the setup code enables you to control those components using the remote control supplied with
this unit (without connecting system control cords). To register setup codes for your remote controllable KENWOOD audio components, see
“Setup for controlling AV components”.
(
SL16 XS8