Panasonic AJ-HD1800P - Manual (Page 106)

106
Setup menus
(continued)
<AUDIO> (continued)
*1 When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or the 50 Hz
(HD, SD) mode is selected in System Menu No. 25 (SYSTEM
FREQ), this item is not displayed.
No./Item Description of setting
734*
1
PB FADE
For selecting how to process the audio edit
points (IN points and OUT points) during
playback.
0000 AUTO
The status established during recording is fol-
lowed.
0001 CUT
Forcibly cut
0002 FADE
Forcibly faded
735
HD EMBD AUD
For selecting whether to superimpose the audio
data on the HD SDI output.
0000 OFF
The audio data is not superimposed.
0001 ON
The audio data is superimposed.
736
SD EMBD AUD
For selecting whether to superimpose the audio
data on the SD SDI output.
0000 OFF
The audio data is not superimposed.
0001 ON
The audio data is superimposed.
737
MONI MIX
For selecting the mixed signals for the
headphone monitor (Lch and/or Rch).
0000 OFF
Neither the Lch nor Rch signals are mixed.
0001 L
Only the Lch signals are mixed.
0002 R
Only the Rch signals are mixed
0003 L/R
Both the Lch and Rch signals are mixed.
<Notes>
z At the OFF setting, the signals to be output to
monitor L (or monitor R) are switched to CH1,
CH2, CH3 and so on each time the “L” or “R”
button is pressed. The selected signals are
displayed below the audio level meter.
z At the L, R or L/R setting, the signals of a
multiple number of channels can be mixed and
output. When the number key corresponding to
the channel whose signals are to be monitored is
pressed while the “L” (or “R”) button is held down,
that channel is selected. The selected channel is
displayed below the audio level meter.
(Alternatively, the same steps can be taken to
de-select a channel which has already been
selected.) However, only up to 2 channels
among the CH1-CH4 channels and up to 2
channels among the CH5 to CH8 channels can
be selected.
738
CH1 CUE SEL
For selecting the CH1 output status of the main
signal line in the search mode.
0000 OFF
The CUE signal is not output.
0001 ON
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to
[Audio outputs in the search mode] (page 109).
No./Item Description of setting
739
CH2 CUE
SEL
For selecting the CH2 output status of the main
signal line in the search mode.
0000
OFF
The CUE signal is not output.
0001 ON
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to
[Audio outputs in the search mode] (page 109).
740
CH3 CUE
SEL
For selecting the CH3 output status of the main
signal line in the search mode.
0000 OFF
The CUE signal is not output.
0001 ON
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to
[Audio outputs in the search mode] (page 109).
741
CH4 CUE
SEL
For selecting the CH4 output status of the main
signal line in the search mode.
0000 OFF
The CUE signal is not output.
0001 ON
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to
[Audio outputs in the search mode] (page 109).
742
CH5 CUE
SEL
For selecting the CH5 output status of the main
signal line in the search mode.
0000 OFF
The CUE signal is not output.
0001 ON
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to
[Audio outputs in the search mode] (page 109).
743
CH6 CUE
SEL
For selecting the CH6 output status of the main
signal line in the search mode.
0000 OFF
The CUE signal is not output.
0001 ON
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to
[Audio outputs in the search mode] (page 109).
744
CH7 CUE
SEL
For selecting the CH7 output status of the main
signal line in the search mode.
0000 OFF
The CUE signal is not output.
0001 ON
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to
[Audio outputs in the search mode] (page 109).