Panasonic AJ-HD1800P - Manual (Page 107)

107
Setup menus
(continued)
<AUDIO> (continued)
*1 When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or the 50 Hz
(HD, SD) mode is selected in System Menu No. 25 (SYSTEM
FREQ), this item is not displayed.
The underlining (__) denotes the factory setting mode.
No./Item Description of setting
745
CH8 CUE
SEL
For selecting the CH8 output status of the main
signal line in the search mode.
0000 OFF
The CUE signal is not output.
0001 ON
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to
[Audio outputs in the search mode] (page 109).
746
MONI CH
SEL
For selecting the monitor output.
0000 MANU
The signal selected by the MONITOR SELECT
button is output.
0001 AUTO
The PCM audio signal is output in the j1.0k to
i2.0k speed range; the CUE signal is automati-
cally output at all other speeds.
0002 PCM
The PCM audio signal is output in the j32k to
i32k speed range.
<Notes>
z When “AUTO” is selected and a tape in any
format except DVCPRO HD-LP is played back,
the PCM audio signals are output in the
j1.0k
to +1.1 k speed range.
z This setting takes effect when the L and R
MONITOR SELECT switches on the VTR’s front
panel have selected a channel from CH1 to CH8.
(If they have selected CUE, the CUE signal is
output at all speeds regardless of this me
nu
item’s setting.)
747
MON AUTO
SEL
For selecting the channel for the monitor output
to be switched to CUE.
When a setting other than “MANU” has been
selected for setup menu item No.746 (MONI CH
SEL), the CUE signal is automatically output to the
monitor output in accordance with the operation
mode, and the monitor channel to be switched to
CUE is selected automatically.
0000 L/R
The CUE signal is output both to the Lch and
Rch.
0001 L
The CUE signal is output to the Lch only.
0002 R
The CUE signal is output to the Rch only
<Note>
For audio output conditions, refer to [Audio outputs
in the search mode] (page 109).
748
MONI SEL
INH
For selecting whether to enable or inhibit the
operation of the MONITOR SELECT button on
the front panel.
0000 OFF
The button’s operation is enabled.
0001 ON
The button’s operation is inhibited.
0002 ON1
In the FULL display mode, operation is prohib-
ited; in the FINE display mode only, operation is
enabled.
<Note>
Whether to enable or inhibit the button’s operation
can be selected for channels whose signals have
not been mixed by the setup menu item No.737
(MONI MIX) setting.
No./Item Description of setting
749
*1
AUDIO PB
VR
For selecting whether the playback level
adjustment controls are to function in the EE
mode when INT SG has been selected on the
<AUDIO> function menu.
0000
DIS
The INT SG output level is fixed at the UNITY
level.
0001 ENA
The INT SG output level can be varied using the
playback level adjustment controls.
750
ANA CH1
SEL
For selecting the signal to be output to analog
output CH1.
0000 CH1
The CH1 signal is output
0001 CH5
The CH5 signal is output
751
ANA CH2
SEL
For selecting the signal to be output to analog
output CH2.
0000 CH2
The CH2 signal is output.
0001 CH6
The CH6 signal is output
752
ANA CH3
SEL
For selecting the signal to be output to analog
output CH3.
0000 CH3
The CH3 signal is output
0001 CH7
The CH7 signal is output
753
ANA CH4
SEL
For selecting the signal to be output to analog
output CH4.
0000 CH4
The CH4 signal is output
0001 CH8
The CH8 signal is output
754
SD SDI CH1
SL
For selecting the audio CH1 signal to be
superimposed onto the SD SDI output.
0000 CH1
The CH1 signal is output.
0001 CH2
The CH2 signal is output.
0002 CH3
The CH3 signal is output.
0003 CH4
The CH4 signal is output.
0004 CH5
The CH5 signal is output.
0005 CH6
The CH6 signal is output.
0006 CH7
The CH7 signal is output.
0007 CH8
The CH8 signal is output.