Panasonic HD1700pe - Manual (Page 30)

30
Automatic Editing
(deck-to-deck)
1
Select the editing mode.
ASSEM button:
Assemble (frame-to-frame continuity) editing is
performed in this mode.
INSERT button:
Insert editing is performed in this mode.
2
On the time code display, select the channels to be
edited.
ASSEM:
Set ASSEM to ON using the
button.
INSERT:
To select V, A1, A2, A3, A4 and CUE channels,
press the
to buttons; to select A5, A6, A7,
A8 and TC channels, press the + to
+ buttons. The highlighted channels
will now be edited.
F6 SHIFT
F2 SHIFT
F6 F1
F1
3
Press the PLAYER or RECORDER button to select
the VTR which is to be operated.
[Setting for editing using two VTRs]
PLAYER:
Press this button if the player VTR is to be
operated to register the edit points.
RECORDER:
Press this button if the recorder VTR (this VTR) is
to be operated to register the edit points.
F1 SHIFT F2 F3 F4 F5 F6
[ASSEM screen]
IN point OUT point
F1 SHIFT F2 F3 F4 F5 F6
[INSERT screen]
IN point OUT point
AUDIO IN point
Marker
AUDIO OUT point
1
Locate the edit IN point by performing the jog or
shuttle operation. Set the tape to the still picture
status at the desired position.
For a detailed description of the jog and shuttle
operations, refer to page 27.
2
Press the IN button and SET button together.
The edit IN point is now registered.
The edit IN point value appears on the display.
4
Press the OUT button and SET button together.
The edit OUT point is now registered.
The edit OUT point value appears on the display.
5
3
Locate the edit OUT point by performing the jog or
shuttle operation. Set the tape to the still picture
status at the desired position.
Registering the edit points Selecting the editing mode
Match frame processing function
When two VTRs are used to perform the editing
operations, there will be a total of 4 edit points: the IN
and OUT points for the player and the IN and OUT points
for the recorder. However, the last point is automatically
calculated so only three of the edit points need to be
registered.
Negative duration function
Use setup menu items No.300 (IN/OUT DEL) and
No.301 (NEGA FLASH) in combination.
POWER OFF ON
HEADPHONES
PUSH
LOCK
FULL
CH CONDITION MONITOR FULL/FINE REMOTE
L R 9P 50P RS-232C
CH 1 2 3 4 5 6 7 8 CUE
XL/L/M-cassette
Do not insert S-cassette without adapter
EJECT
AUDIO CH SELECT
SHIFT
ABC DEF GHI
JKL MNO PQRS
PREVIEW/ REVIEW PRE- ROLL
A IN A OUT
HOME RF1 ASSEM ADJUST SHTL
REV FWD
VAR JOG
STAND BY RECORDER INPUT CHECK PLAYER
SERVO
EDIT PLAY REC
REW STOP FF
REC INHIBIT
PUSH-INTER
INSERT
RF2
VIDEO UNITY TC CUE
AUDIO UNITY DIAG MENU
TRIM
SET
IN OUT
AUTO
EDIT
7 8 9
4 5 6 BS
TUV WXYZ
1 2 3 ENT
0 C T F
F1 F2 F3 F4 F5 F6
CH 1 CH 5 CH 2 CH 6 CH 3 CH 7 CH 4 CH 8
FULL REC P8 REC P8 REC P8 REC P8
1, 3 2, 4 5
The edit points can be registered directly using the
number keys.
1. Select the <ASSEMBLE> or <INSERT> menu.
2. Press the
button to highlight the edit point. Turn
the ADJUST dial to move the highlighting to the IN
point or OUT point.
3. Press the button again, and input the desired edit
point directly using the number keys. Turn the
ADJUST dial to move from one digit to the next.
4. Press the button to register the point.
To abort the registration at any time, press the
button.
To reset a particular edit point (to 00:00:00:00), press
the
button, align the highlighting with the edit
point concerned, and press the button again.
Next, press the button and button together.
Finally, press the button to register the point. ENT
0 F
T
T
C
ENT
T
T