Parts and their functions, Front panel, Push lock – Panasonic HD1700pe User Manual

Page 9: Push-inter, Unity

Advertising
background image

9

POWER OFF

ON

HEADPHONES

PUSH
LOCK

FULL

CH CONDITION

MONITOR

FULL/FINE

REMOTE

L

R

9P

50P

RS-232C

CH

1

2

3

4

5

6

7

8

CUE

XL/L/M-cassette

Do not insert S-cassette

without adapter

EJECT

AUDIO CH SELECT

SHIFT

ABC

DEF

GHI

JKL

MNO

PQRS

PREVIEW/

REVIEW

PRE-
ROLL

A IN

A OUT

HOME

RF1

ASSEM

ADJUST

SHTL

REV

FWD

VAR

JOG

STAND BY

RECORDER INPUT CHECK

PLAYER

SERVO

EDIT

PLAY

REC

REW

STOP

FF

REC INHIBIT

PUSH-INTER

INSERT

RF2

VIDEO

UNITY

TC

CUE

AUDIO

UNITY

DIAG

MENU

TRIM

SET

IN

OUT

AUTO

EDIT

7

8

9

4

5

6

BS

TUV

WXYZ

1

2

3

ENT

0

C

T

F

F1

F2

F3

F4

F5

F6

CH

1

CH

5

CH

2

CH

6

CH

3

CH

7

CH

4

CH

8

FULL

REC

P8

REC

P8

REC

P8

REC

P8

<

9

;

8

: =

Front panel

8 MONITOR SELECT buttons

These buttons are used to select the audio signals
which are to be output to the monitor L and R
connectors and headphones jack.
When OFF has been selected as the

M

MIX setting on the <AUDIO SHIFT2> menu
(factory setting):
Each time the L (or R) button is pressed, the
signal to be output to the monitor L (or R)
connector is changed in the following sequence
and displayed on the audio level meter: CH1

>

CH2

> CH3> CH4 > CH5 > CH6 > CH7 >

CH8

> CUE > CH1, etc.

When L, R or L/R has been selected as the

M MIX setting on the <AUDIO SHIFT2> menu:
At this setting, the signals of a multiple number of
channels can be mixed and output.
When the number key corresponding to the
channel whose signals are to be monitored is
pressed while the L (or R) button is held down,
that channel is selected and its signals are
displayed on the audio level meter. (By
performing the same operation, the selected
channel can be de-selected.)
However, a maximum of only two channels from
CH1 to CH4 and a maximum of only two
channels from CH5 to CH8 can be selected.
Example of channels which can be selected:
CH1 i CH3 i CH5 iCH8 “ OK
CH1 + CH2 + CH4 “ NG

9 METER (FULL/FINE) selector button

This button is used to select the scale display for the
audio level meter.
FULL mode: Depending on the setting selected for the

setup menu item No.763 (METER SCALE)*, either the

to 0 dB (reference level: j20 dB/j18 dB**) or j¶

to i20 dB (reference level: 0 dB) range is displayed.

FINE mode: Depending on the setting selected for the

setup menu item No.763 (METER SCALE)*, either the
j

24 to j15 dB (reference level: j20 dB/j18 dB**) or

j

4 to i5 dB (reference level: 0 dB) range is displayed

on a scale with 0.5 dB increments.

* This menu is not displayed for AJ-HD1700E.
** j20 dB is applied for AJ-HD1700P and j18 dB is for AJ-HD1700E.

F6

F6

Parts and Their Functions

: REMOTE buttons and RS-232C display

These buttons are used when this VTR is to be
controlled from an external component using the
REMOTE, RS-232C or parallel connector.
9P:

When this button is pressed for 2 or more

seconds, its LED lights, and the 9-pin REMOTE
connector is selected.

50P:

When this button is pressed for 2 or more

seconds, its LED lights, and it is possible to control
the VTR from a unit which has been connected using
the 50-pin parallel mode connector.

RS-232C display: This LED lights when communi-

cation has been enabled between the VTR and the
unit which has been connected to the RS-232C
connector.

; AUTO OFF lamp

This lamp lights when a problem has occurred with
the VTR’s operation, and details of the problem
appear on the time code display.

< LCD monitor

This monitor is used to check the tape’s playback
pictures and EE pictures.
When an HD tape is played back, the signals are down-
converted and displayed in the letter-box screen format.
When an SD tape is played back, the signals are
displayed using a 4:3 aspect ratio.
On-screen menus can also be displayed on the monitor.
If the VTR is left in a state where no controls on the front
panel are operated or where the tape is not running, the
monitor display is automatically turned off in order to
protect the monitor. When the next VTR operation is
started, the monitor display comes back on.
<Note>
Although the LCD monitor has been manufactured
using technology with extremely high levels of
precision, some pixels may be missing from parts of
the screen or some pixels may remain lighted.
These missing or lighted pixels will not be recorded.
It should also be borne in mind that this is not
indicative of a malfunction.

= Function buttons

These buttons are used to perform the operations of
the function menus (see page 38 for details) and
setup menus.

: This is used to switch the pages of the current

function menu (

to

).

to : These are used to change the settings of

the setting items enclosed in the frame at the bottom of
the time code display.
To change a setting, keep pressing the corresponding
function button (

to

) until the desired

numerical value appears; alternatively, press the
corresponding function button to highlight the setting of
the setting item, and then turn the ADJUST dial until
the desired numerical value is obtained.

F6

F1

F6

F1

F6

F1

SHIFT

Advertising