Panasonic WJ-HD220 - Manual (Page 27)

27
● Post-alarm Recording (POST ALM
REC)
This setting specifies the duration of alarm recording after
an alarm input. Functions active during alarm recording are
buzzer beeping, ALARM LED indication, "ALARM" status
display, and the ALARM OUT signal.
1. Move the cursor to POST ALARM REC with the [D] or
[C] button.
2. Select the desired duration with the JogDial.
The default value is 10 seconds.
The unit will revert to the previous status when the time
has elapsed.
Available times (seconds): 5, 10, 20, 30
Available times (minutes): 1, 1.5, 2, 3, 6
Continue: Recording continues until the [RESET] but-
ton is pressed, or the RESET IN signal is supplied to
the rear panel.
Manual: Recording continues for as long as the alarm
input is active, or at least for 10 seconds if the input
turns inactive earlier.
● Dynamic Recording (DYNAMIC REC)
This setting specifies the recording pattern on the disk
when one or more alarms operate.
1. Move the cursor to DYNAMIC REC with the [D] or [C]
button.
2. Select the parameter with the JogDial, and press the
JogDial.
The default is OFF.
ALM-MULTI: Alarmed channels are recorded with pri-
ority over others.
OFF: All channels are recorded with the same priority.
● Trigger Action Setup (TRIGGER
ACTION SETUP)
This setting specifies the two roles of alarm recording and
alarm control functions (Refer to page 47) in the post-alarm
sequence.
When combination cameras are connected to VIDEO IN 1-4
on the rear panel, you can select a preset position for cam-
eras 1-4. The camera will move to the preset position when
an alarm other than VMD arises for the camera.
Notes:
• The preset position assignment on the TRIGGER
ACTION SETUP menu is not available for each PROG n
(1 - 4) SETUP menu, but available only for the REC
SETUP menu.
• You need to preset desired positions for the camera
prior to operation.
• VMD will not move the camera to the preset position.
1. Move the cursor to TRIGGER ACTION SETUP
O, and
press the JogDial.
The TRIGGER ACTION SETUP menu opens.
2. Move the cursor to the channel.
3. Select a mode with the JogDial, and press the JogDial.
The default is REC&ALM.
OFF: Disables alarm recording or warning.
REC&ALM: Enables both alarm recording and warning.
REC: Enables alarm recording, but disables warning.
4. The cursor is at the PRESET column. Select a preset
parameter with the JogDial, and press the JogDial.
1-64: Moves the camera to the specified preset posi-
tion.
HOME: Moves the camera to the home position.
– –: Does not move the camera.
5. Repeat steps 2, 3 and 4 until all channels are set.
6. Press the [SETUP/ESC] button to return to the PROG1
SETUP, NO. 1 menu.
● Camera Recording Setup (CAM REC
SETUP)
This setting is provided for the purpose of saving disk
space. Setting allows each camera channel to be enrolled
in all recording modes or exclusively in alarm recording.
1. Move the cursor to CAM REC SETUP, and press the
[SET] button. The CAM REC SETUP menu opens.
2. Move the cursor to the camera channel with the [D] or
[C] button.
CAM REC SETUP
CAM MODE
1 REC
2 REC
3 REC
4 ALM-ONLY
5 REC
6 ALM-ONLY
7 REC
8 REC
TRIGGER ACTION SETUP
CAM MODE PRESET
1
→ REC&ALM ––
2
→ REC&ALM ––
3
→ REC&ALM ––
4
→ REC&ALM ––
5
→ REC&ALM
6
→ REC&ALM
7
→ REC&ALM
8
→ REC&ALM