Cp3 bt26 – National CP3BT26 User Manual
Page 169
169
www.national.com
CP3
BT26
22.3.1
UART Receive Data Buffer (UnRBUF)
The UnRBUF register is a byte-wide, read/write register
used to receive each data byte.
22.3.2
UART Transmit Data Buffer (UnTBUF)
The UnTBUF register is a byte-wide, read/write register
used to transmit each data byte.
22.3.3
UART Baud Rate Prescaler (UnPSR)
The UnPSR register is a byte-wide, read/write register that
contains the 5-bit clock prescaler and the upper three bits of
the baud rate divisor. This register is cleared upon reset.
The register format is shown below.
UPSC
The Prescaler field specifies the prescaler val-
ue used for dividing the System Clock in the
first stage of the two-stage divider chain. For
the prescaler factors corresponding to each 5-
bit value, see Table 69.
UDIV10:8
The Baud Rate Divisor field holds the three
most significant bits (bits 10, 9, and 8) of the
UART baud rate divisor used in the second
stage of the two-stage divider chain. The re-
maining bits of the baud rate divisor are held
in the UnBAUD register.
22.3.4
UART Baud Rate Divisor (UnBAUD)
The UnBAUD register is a byte-wide, read/write register that
contains the lower eight bits of the baud rate divisor. The
register contents are unknown at power-up and are left un-
changed by a reset operation. The register format is shown
below.
UDIV7:0
The Baud Rate Divisor field holds the eight
lowest-order bits of the UART baud rate divi-
sor used in the second stage of the two-stage
divider chain. The three most significant bits
are held in the UnPSR register. The divisor
value used is (UDIV[10:0] + 1).
22.3.5
UART Frame Select Register (UnFRS)
The UnFRS register is a byte-wide, read/write register that
controls the frame format, including the number of data bits,
number of stop bits, and parity type. This register is cleared
upon reset. The register format is shown below.
UCHAR
The Character Frame Format field selects the
number of data bits per frame, not including
the parity bit, as follows:
00 – 8 data bits per frame.
01 – 7 data bits per frame.
10 – 9 data bits per frame.
11 – Loop-back mode, 9 data bits per frame.
USTP
The Stop Bits bit specifies the number of stop
bits transmitted in each frame. If this bit is 0,
one stop bit is transmitted. If this bit is 1, two
stop bits are transmitted.
0 – One stop bit per frame.
1 – Two stop bits per frame.
UXB9
The Transmit 9th Data Bit holds the value of
the ninth data bit, either 0 or 1, transmitted
when the UART is configured to transmit nine
data bits per frame. It has no effect when the
UART is configured to transmit seven or eight
data bits per frame.
UPSEL
The Parity Select field selects the treatment of
the parity bit. When the UART is configured to
transmit nine data bits per frame, the parity bit
is omitted and the UPSEL field is ignored.
00 – Odd parity.
01 – Even parity.
10 – No parity, transmit 1 (mark).
11 – No parity, transmit 0 (space).
U3OVR
FF F270h
UART3 Oversample
Rate Register
U3MDSL2
FF F272h
UART3 Mode Select
Register 2
U3SPOS
FF F274h
UART3 Sample
Position Register
7
0
URBUF
7
0
UnTBUF
7
3
2
0
UPSC
UDIV10:8
Table 70
UART Registers
Name
Address
Description
7
0
UDIV7:0
7
6
5
4
3
2
1
0
Reserved
UPEN
UPSEL
UXB9
USTP
UCHAR