Alpha Technologies DSM3 for XM3 - Technical Manual - Manual (Page 88)

88 745-814-B11-001, Rev. C (03/2014)
Parameter OID Description Access Type Value
SOFTWARE DOWNLOAD
atiMgmtSysDownloadCfgCheckProgress
1.3.6.1.4.1.926.1.3.2.1.12.0 DSM Setup File Marker Read Only Integer 3
atiMgmtSysDownloadReCfgTime 1.3.6.1.4.1.926.1.3.2.1.13.0 Hours between download of setup file Read/Write Integer 24 (Default)
atiMgmtSysDownloadFromCM 1.3.6.1.4.1.926.1.3.2.1.14.0 Allows the auto reimaging from the Cable
Modem to be disabled or to happen only once.
Manufacturing default value is 1.
Read/Write Integer 1: allow(1)
2: prevent(2)
3: onceOnly(3)
atiMgmtSysDownloadTftpServerAddressType 1.3.6.1.4.1.926.1.3.2.1.15.0 Address mode of
atiMgmtSysDownloadTftpServerAddress.
Read/Write Integer "1: IPv4(1)
2: IPv6(2)"
atiMgmtSysDownloadTftpServerAddress 1.3.6.1.4.1.926.1.3.2.1.16.0 Address of download TFTP server.
If the TFTP server is unknown, return
the zero-length address string (see the
TextualConvention).
If atiMgmtSysDownloadTftpAddress is
also implemented in this agent, this object
is tied to it. A set of this object to an IPv4
address will result in also setting the value
of atiMgmtSysDownloadTftpAddress to that
address. If this object is set to an IPv6 address,
atiMgmtSysDownloadTftpAddress is set to
0.0.0.0. If atiMgmtSysDownloadTftpAddress is
set,this object is also set to that value. Note that
if both are set in the same action, the order of
which one sets the other is undefined.
Read/Write Octet String 0.0.0.0 (Default)
atiMgmtSysDownloadConfigServerAddressType 1.3.6.1.4.1.926.1.3.2.1.17.0 Address mode of
atiMgmtSysDownloadConfigServerAddress.
Read/Write Integer 1: IPv4(1)
2: IPv6(2)
atiMgmtSysDownloadConfigServerAddress 1.3.6.1.4.1.926.1.3.2.1.18.0 "Address of download TFTP server.
If the TFTP server is unknown,
return the zero-length address string
(see the TextualConvention). If
atiMgmtSysDownloadConfigAddress is
also implemented in this agent, this object
is tied to it. A set of this object to an IPv4
address will result in also setting the value of
atiMgmtSysDownloadConfigAddress to that
address. If this object is set to an IPv6 address,
atiMgmtSysDownloadConfigAddress is set to
0.0.0.0. If atiMgmtSysDownloadConfigAddress
is set, this object is also set to that value. Note
that if both are set in the same action, the order
of which one sets the other is undefined."
Read/Write Octet String 0.0.0.0 (Default)
WEB SERVER ENABLE
atiMgmtSysHttpPrams
1.3.6.1.4.1.926.1.3.2.2.4 Object Identifier
atiMgmtSysHttpEnabled 1.3.6.1.4.1.926.1.3.2.2.4.1.0 Access to DSM3 via Web Browser Read/Write Integer 1=Disable
2=Enable (default)
SIMPLE NETWORK TIME PROTOCOL
atiMgmtSysServers
1.3.6.1.4.1.926.1.3.2.3.0 Object Identifier
atiMgmtSysServSntp 1.3.6.1.4.1.926.1.3.2.3.1.0 IP Address of SNTP Server (Optional) Read/Write IP Address 0.0.0.0 (default)
ENVIRONMENTAL MANAGER
atiMgmtSysTempMgr
1.3.6.1.4.1.926.1.3.2.4.0 Object Identifier
atiMgmtSysTempCtrl 1.3.6.1.4.1.926.1.3.2.4.1.0 Environmental Control Read/Write Integer 1=off (default)
2=OnTimer
3=OnTemp
4=onTimerTemp
5=on
atiMgmtSysTempStatus 1.3.6.1.4.1.926.1.3.2.4.2.0 Environmental Control Feedback State Read Only Integer 1=Contact Open (default)
2=Contact Closed
atiMgmtSysTempMode 1.3.6.1.4.1.926.1.3.2.4.3.0 Environmental Mode (Heat/Cool) Read/Write Integer 1=Heater (default)
2=Cooler
atiMgmtSysTempActiveState 1.3.6.1.4.1.926.1.3.2.4.4.0 Environmental Control Contact State (Open/
Closed)
Read/Write Integer 1=Closed (default)
2=Open
atiMgmtSysTempTemperature 1.3.6.1.4.1.926.1.3.2.4.5.0 Environment Temperature Read/Write Integer 1..70ºC
atiMgmtSysTempHysteresis 1.3.6.1.4.1.926.1.3.2.4.6.0 Environmental Temperature Hysteresis Read/Write Integer 1..10ºC
atiMgmtSysTempTimer 1.3.6.1.4.1.926.1.3.2.4.7.0 Environmental Default Timer Read/Write Integer 0..1440 (30 minute default,
15 minute increments)
atiMgmtSysTempCountdown 1.3.6.1.4.1.926.1.3.2.4.8.0 Environmental Timer Time Remaining Read Only Integer 0..1440 (in minutes)
atiMgmtSysTempStatusInvert 1.3.6.1.4.1.926.1.3.2.4.9.0 State inverted to match the type of relay
operation on the heater mat controller
Read/Write Integer 1=No invert (default)
2=Invert
10.1 Definitions and Settings
10.0 Alpha MIB Parameters