Document Outline

• Introduction
  • Additional Documentation
    • Drawing Categories
    • Tech Notes
• Overview
  • Data Logging
  • Wideband Lambda
  • Options
  • ECU Inputs & Outputs
    • Main Engine Sensors
    • Optional Sensors
    • Fuel Injector Outputs
    • Ignition Outputs
    • Auxiliary Outputs
    • CAN Communications
    • RS232 Serial Communications
  • Calibration & Setup
    • Calibration Tables
    • Setup Parameters
  • ECU Functions
    • Functions
    • Digital Input Functions
    • Auxiliary Output Functions
• MoTeC Software
  • PC Requirements
  • Connecting a PC to the ECU
  • Installing the Software
  • Starting the Software
  • ECU Manager Software
  • Data Logging
    • Unloading the Logged Data
    • Data Logging Analysis
• Installation
  • Throttle Position or MAP Load Sensing
    • Turbo Charged Engines
    • Normally Aspirated Engines
  • Sensors
    • Throttle Position Sensor
    • MAP Sensor
      • If Used for Manifold Pressure Sensing
      • If used for Barometric Pressure Sensing
    • Air Temp Sensor
    • Engine Temp Sensor
    • Trigger Sensors (REF & SYNC)
      • REF Sensor
      • SYNC Sensor
      • REF / SYNC Alignment
    • Exhaust Gas Sensor (Lambda Sensor)
  • Wiring
    • Wiring Drawings
    • Wiring Reliability
      • Ground Wiring
      • Power Wiring
      • Spark Plug Leads
      • Terminal Crimping
      • Terminal Damage
      • Wire Splicing
      • Wire Strain
      • Wire Movement
      • Heat
  • Fuel System
    • /
    • Lift Pump
    • Swirl Pot
    • Pressure Pump
    • Filters
    • Fuel Lines
    • Fuel Rails
    • Fuel Pressure Regulator
      • If Using Manifold Pressure Load Sensing
      • If Using Throttle Position Load Sensing
    • Fuel Injectors
      • Sizing
      • Flow Rate Matching
      • Fuel Pressure
      • Current
      • Pulse Width
      • Duty Cycle
  • Ignition System
    • Ignition System Types
      • CDI Distributed
      • HEI Distributed
      • Multicoil (HEI or CDI)
        • Coil per plug
        • Double Ended Wasted Spark
    • Ignition System Wiring & Setup
    • Distributor Button Alignment
    • Spark Plug Leads
  • Auxiliary Valves
  • ECU Mounting
  • ECU Cleaning
• Initial Setup
  • Main Setup
    • Injectors
    • Calculation Methods
    • Number of Cylinders
    • Trigger Setup
    • Ignition
  • Sensor Setup
    • Throttle Position Sensor Hi / Lo
    • REF / SYNC Sensor Setup
    • Sensor Calibrations
  • Input / Output Functions
  • Other Functions
• Initial Calibration
  • Fuel Tables
    • Fuel - Main Table
    • Fuel - Air Temp
    • Fuel - Engine Temp
    • Fuel - MAP
    • Fuel - Cold Start
    • Fuel - Acceleration Enrichment
    • Other Fuel Compensation Tables
  • Ignition Tables
    • Ignition - Main Table
    • Ignition - Air Temp
    • Other Ignition Compensation Tables
• Initial Starting Procedure
  • Pre Start Checks
    • Calibration Tables & Setup Parameters
    • Power to the ECU
    • Diagnostic Errors
      • Sensor Errors
    • Test the Sensors
    • Test the Ignition
    • Test the Injectors
    • Initial Cranking
    • Cranking Ignition Timing
  • Starting
    • Fuel System
    • Fuel Overall Trim
    • If the engine won’t start
  • After Start Checks
    • Ignition Timing Check
    • Fuel Pressure
    • Operational Diagnostics Errors
      • Injector Errors
      • Over Duty
      • REF / SYNC Errors
        • REF Error
        • No REF
        • SYNC Error
        • No SYNC
        • Multiple REF / SYNC Errors
• Calibration
  • Warning Alarms
  • Ensure that the engine is “On Site”
  • Site Tables
  • Dyno Calibration
  • Fuel - Main Table
  • Ignition - Main Table
  • Fuel - Injection Timing
  • Fuel - Cold Start
  • Other Calibration Tables
  • Data Logging & Road Testing
• ECU Manager Software
  • Introduction
    • PC Requirements
    • Connecting a PC to the ECU
    • Installing the Software
  • Basics
    • Starting ECU Manager
    • Online Help
    • Main Menu
      • Unavailable Menu Items
    • Button Bar (Toolbar)
    • Status Bar
  • Calibration Files
    • Creating a New Calibration File
    • Sending a Calibration File to the ECU
    • Changing the Comments
  • Versions & Upgrading
    • Matching Versions
    • Upgrading the ECU
    • Calibration File Versions
    • Minor Version Updates
    • Software Version Release Notes
  • Screen Layouts
    • Layout Pages
    • Layout Objects
    • Adjust Tables and Adjust Graph Objects
      • Adjust Tables
      • Adjust Graphs
      • Graph Table
      • Y Axis Reversing
  • Making Adjustments
    • On Line / Offline
      • Online (ECU Connected)
      • Offline (ECU not Connected)
    • Closing the ECU or File
    • Warning Alarms
    • Help
    • Selecting the Adjust Table
      • /
      • Fuel / Ignition Toggle (F5 key)
      • F6, F7, F8 Key Assignment
    • Changing Table Values
      • Selecting the Item to be Adjusted
      • Make sure the engine is “On Site”
        • Table Indicators
        • Table Target
      • Up / Down Adjustment
      • Locking in the New Value
      • Direct Entry
      • Maths Operations
      • Block Operations
      • Quick Lambda
      • Set Indicators (*)
    • Tools
      • Compare Mode On / Off
      • Select Compare File
      • Jump to Site
      • Quick Lambda
      • Quick Lambda + Copy Up & Right
      • Lambda Was
      • Overall Trim Table
      • Interpolate Vertical Column
      • Interpolate Horizontal Row
      • Copy Vertical Column Right
      • Copy Horizontal Row Up
      • Copy Site Up And Right
      • Reverse Y-Axis
      • Toggle Table Mode
      • Set All Values To Current
      • Reset ECU
      • Clear All *
      • Clear Current *
      • Set with *
      • Copy Table from Another File
      • Import CSV File
      • Export CSV File
      • Insert Site
      • Delete Site
  • View Screen
  • Testing the ECU Outputs
  • ECU Password
  • File Encryption
  • Enabling ECU Options
  • Keyboard Reference
• Appendices
  • Appendix A: General Specifications
    • Physical
    • Power Supply
    • Operating Temperature
  • Appendix B: Sensor Supplies
    • Maximum Current
    • Accuracy / Temp Drift
    • Protection
  • Appendix C: Input Characteristics
    • Analogue Voltage Inputs
    • Analogue Temp Inputs
      • When used as Switch Inputs
    • Lambda Inputs
      • Wideband
      • Narrow Band
    • Digital Inputs
  • Appendix D: Auxiliary Output Characteristics
  • Appendix E: Ignition Output Characteristics
  • Appendix F: Injector Output Characteristics
    • Peak and Hold Mode
    • Saturated Drive Mode
    • High / Low Injection
  • Appendix H: Wire Specifications
    • M22759/16 Wire Ratings (For Various Wire Gauges)
  • Appendix J: CAN Wiring - Multiple Devices
    • Short CAN Bus
    • Single Device
  • Appendix K: CAN Bus Wiring - Single Device
    • 5 Pin Connector Type :
  • Appendix L: Pin list by Function
    • Battery
    • Sensor Supplies
    • Auxiliary Outputs
    • Ignition Outputs
    • Injector Outputs
    • Pin No Abbrev Description
    • Analogue Voltage Inputs
    • Analogue Temp Inputs
    • Digital Inputs
    • Trigger Inputs
    • Lambda Inputs
    • Comms
  • Appendix M: Wiring Schematic