LEDGlow 4pc.-10pc. Single Color Wireless LED Underbody Kit User Manual

4pc – 10pc single color underbody kit

Advertising
background image

4pc – 10pc Single Color Underbody Kit


Warning:

Please check your state and local laws before installing this LED underbody lighting kit. Every state has different policies and procedures in place regarding

aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while using this underbody kit. This kit is for off road use only.

Warning:

The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.

The control box that is used to power this lighting kit must be installed in a dry location! Having this part exposed to water or the elements will cause the kit’s
controller to fail. Any water damage or corrosion to this part will VOID all warranties.


PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED UNDERBODY KIT.

Underbody Kit Includes:

(2) 36 Inch tubes (A)

(2) 48 Inch Tubes (B)

(1) Control Box

(1) 4 Button Wireless Remote

(1) Underbody Tube Junction Box

(14) Underbody Tube Brackets

(25) Zip Ties

(30) Large Screws

(2, 4, or 6) 15 Inch Interior Tubes (if you purchased add on interior tubes)

(1) Interior Tube Junction Box (if your purchased add on interior tubes)

Underbody Installation

1.

Arrange the tubes out on the ground and test the kit to ensure proper functionality before installing. If you are installing interior tubes as well, mock them up
where you plan on installing them to ensure proper illumination.

2.

Temporarily power your kit with any 12 volt source to ensure it is functioning properly before you move forward with the installation. Simply connect the red
wire to the positive terminal and the black wire to any good ground source. Power the kit on to ensure full functionality. Once you have determined the kit is
functioning properly, remove the power from your kit.

3.

Optional: Raise and support the vehicle.

4.

Before mounting the each tube, please refer to the schematic below to ensure correct placement and tube direction.





Warning: If the tubes are not installed correctly the
lighting patterns will not display properly.



Note: The rear 36 inch LED tube has an 18 foot cable so
that you have no issue running it to the control box. Be sure
that this tube is mounted to the rear of your vehicle or you
will have problems later on in the installation.

5.

Once the kit is laid out properly and you have determined that it is functioning properly, you can proceed with the rest of the installation.

6.

First, mount the front tube, with the 13 foot lead wire facing the passenger’s side, to your vehicle using the included mounting brackets and zip ties. Make sure
the tube is at least 8 inches away from any direct heat source and away from all moving parts. Use the included wire ties to secure the underbody tube to the
mounting bracket. IMPORTANT: DO NOT DRILL ANY HOLES OR ATTACH THE MOUNTING BRACKETS TO THE RADIATOR.

7.

Second, mount the driver’s side tube, with the power wire facing the rear of your vehicle, to your vehicle using the included mounting brackets and zip ties. A
good mounting location for this tube is either the pinch weld or side skirt. Be extremely aware of the location of brake lines and fuel lines, and do not
mount the underbody tube too close to the exhaust.
Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the power
wire away from any moving parts. Use the included wire ties to secure the underbody tube to the mounting bracket.

8.

Next, mount the passenger’s side tube, with the power wire facing the rear of your vehicle, to your vehicle using the included mounting brackets and zip ties. A
good mounting location for this tube is either the pinch weld or side skirt. Be extremely aware of the location of brake lines and fuel lines, and do not
mount the underbody tube too close to the exhaust.
Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the power
wire away from any moving parts. Use the included wire ties to secure the underbody tube to the mounting bracket.

9.

Now, mount the rear tube, with the 18 foot power wire facing the driver’s side, to your vehicle using the included mounting brackets and zip ties. Be extremely
aware of the location of brake lines and fuel lines, and do not mount the underbody tube too close to the exhaust.
Leave at least 8 inches between the
exhaust and the underbody tube
. Keep the tube and the power wire away from any moving parts. Use the included wire ties to secure the underbody tube to
the mounting bracket.



Advertising