LEDGlow Single Color Slimline LED Underbody Kit User Manual

Single color slimline underbody kit

Advertising
background image

Single Color Slimline Underbody Kit

Warning:

Please check your state and local laws before installing this LED underbody lighting kit. Every state has different policies and procedures in place regarding aftermarket vehicle accessories.

LEDGlow is not responsible for any fines that you may receive while using this underbody kit. This kit is for off road use only.


Warning:

The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.


The included on/off switch that is used to power this lighting kit must be installed in a dry location! Having this part exposed to water or the elements will cause the kit’s controller to fail.
Any water damage or corrosion to this part will VOID all warranties.


PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED UNDERBODY KIT.

Underbody Kit Includes:

(2) 36 Inch tubes (A & C)

(2) 48 Inch Tubes (B & D)

(1) On/Off Switch


(12) Underbody Tube Brackets

(20) Zip Ties

(12) Large Screws

(1) Self Sealing Tape

Underbody Installation

1.

Arrange the tubes out on the ground and test the kit to ensure proper functionality before installing.

2.

Temporarily power your kit with any 12 volt source to ensure it is functioning properly before you move forward with the installation. Simply connect the red wire to the positive
terminal and the black wire to any good ground source. Power the kit on to ensure full functionality. Once you have determined the kit is functioning properly, remove the power
from your kit.

3.

Optional: Raise and support the vehicle.

4.

Before mounting each tube, please refer to the schematic below to ensure correct placement and tube direction.



Note: Each underbody tube daisy chains to the next
with the included 6 feet of power wire and modular
connectors.

Note: Use the waterproof tape on all connectors to
ensure connections are not exposed to the elements.

5.

Once the kit is laid out properly and you have determined that it is functioning properly, you can proceed with the rest of the installation.

6.

First, mount the front tube to your vehicle, with the male connector facing the passenger side, using the included mounting brackets and zip ties. Make sure the tube is at least 8 inches
away from any direct heat source and away from all moving parts. Use the included wire ties to secure the underbody tube to the mounting bracket. IMPORTANT: DO NOT
DRILL ANY HOLES OR ATTACH THE MOUNTING BRACKETS TO THE RADIATOR.

7.

Second, mount the driver’s side tube, with the male connector facing the rear of the vehicle, to your vehicle using the included mounting brackets and zip ties. A good mounting
location for this tube is either the pinch weld or side skirt. Be extremely aware of the location of brake lines and fuel lines, and do not mount the underbody tube too close to
the exhaust.
Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included wire ties to
secure the underbody tube to the mounting bracket.

8.

Next, mount the passenger’s side tube to your vehicle, with the male connector facing the rear of the vehicle, using the included mounting brackets and zip ties. A good mounting
location for this tube is either the pinch weld or side skirt. Be extremely aware of the location of brake lines and fuel lines, and do not mount the underbody tube too close to
the exhaust.
Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included wire ties to
secure the underbody tube to the mounting bracket.

9.

Now, mount the rear tube to your vehicle, with the connector facing the rear of the vehicle, using the included mounting brackets and zip ties. Be extremely aware of the location of
brake lines and fuel lines, and do not mount the underbody tube too close to the exhaust.
Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube
and the power wire away from any moving parts. Use the included wire ties to secure the underbody tube to the mounting bracket.

10.

Note: 3 brackets are provided for each tube, one for each end and an additional one for the middle of the tube. For a tight fit, you may want to place a very thin layer of the self sealing
tape on the end of each tube and secure the bracket around it to prevent any possible slippage while your vehicle is in motion.

11.

Mount the underbody kit’s on/off switch in a safe and secure location inside of your vehicle. Run the lead power wire from the front underbody tube through a pre-existing hole with a
grommet in your firewall to the control box. If you do not have a pre-existing hole in the firewall you can drill one, just be sure to use a rubber grommet to ensure the lead wire is not
cut or pinched.

12. This underbody kit’s on/off switch can be powered one of two ways.

a.

Connect the red power wire to any 12 volt source. If you need to extend the power wires, be sure to only use 14 or 16 gauge automotive grade wire. If you are running the
power wire to the battery, it must go through the firewall by using an existing grommet or by drilling a hole and adding a new grommet which is available at any auto parts store.
Be sure to install a fuse within 6 inches of the power source. (You will have to install an additional fuse if you have to extend the wires). Do not run the wire through the
door jam, the wire can be pinched and will void all warranties.

b.

This underbody kit can also be powered directly from your vehicle’s fuse box. If you are powering the kit via the fuse box, LEDGlow recommends that you install the wire
using LEDGlow’s Add-a-Circuit which is available on LEDUnderbody.com.

13.

Connect the black wire to a good, unpainted ground source. A couple of good ground sources are under the dash at any main bracket or grounding block, the negative post on your
battery, or any engine ground.

14.

Beginning with Tube A, connect each tube to the next using the modular connectors. Make sure to secure the wires tightly when going around the suspension part and/or exhaust.
Leave at least 8 inches between the exhaust and the underbody tube. If a power wire is pinched, the kit may malfunction and the warranty could be voided. Run the rear tube’s power
wire along one of the side tubes and make sure it is tightly secured.

Advertising