LEDGlow 7 Color LED Interior Lighting Kit User Manual
4pc 7 color led interior lighting kit
4pc 7 Color LED Interior Lighting Kit
Warning:
Please check your state and local laws before installing this LED interior lighting kit. Every state has different policies and procedures in place regarding
aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while using this interior kit. This kit is for off road use only.
Warning:
The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.
The control box that is used to power the interior tubes must be installed in a dry location! Having this part exposed to water or the elements will cause the kit’s
controller to fail. Any water damage or corrosion to this part will VOID all warranties.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED INTERIOR KIT.
Interior Kit Includes:
(4) 9 Inch Tubes
(1) Control Box
(10) Screws
3M Tape for Control Box
Interior Kit Installation
1.
Arrange the interior tubes where you plan on installing them and temporarily power the kit to ensure proper functionality before installing. Once you test the kit
and determine it is functioning properly disconnect the power from the kit.
2.
Mount the first tube to your desired location with the included screws. If you do not want to use the supplied screws, you can use 3M tape, wire ties, or even
Velcro, but they are not included with this kit. Make sure the tube and the lead power wire do not come in contact with any moving parts, for example, the
pedals, steering column, an/or seat tracks.
3.
Mount the remaining three tubes to your desired locations in the same way you did in the previous step. Again, be sure all tubes and lead power wires are not in
the way of any moving parts, for example, the pedals, steering column, an/or seat tracks.
4.
Mount the control box in a readily accessible area using the supplied 3M tape.
Warning: Be sure to mount the control box is in a moisture and heat free area. Any damage to your kit that is a result of moisture or heat will void your
warranty.
5.
Now, that all your control box and tubes are mounted, secure and hide all of the lead wires with wire ties.
6.
This interior kit can be powered one of four ways.
a.
Connect the red power wire to any 12 volt source. If you need to extend the power wires, be sure to only use 14 or 16 gauge automotive grade wire. If
you are running the power wire to the battery, it must go through the firewall by using an existing grommet or by drilling a hole and adding a new
grommet which is available at any auto parts store. Be sure to install a fuse within 6 inches of the power source. (You will have to install an additional
fuse if you have to extend the wires.) If you connect the power wire to a switched 12 volt source, the interior kit may not remember the color and pattern
it was last on before turning off the vehicle. If you connect the power wire to a constant 12 volt source, the interior kit will remember the last color and
pattern it was on prior to turning the vehicle off. Do not run the wire through the door jam, the wire can be pinched and the will void all warranties.
b.
This interior kit can also be powered directly from your vehicle’s fuse box. If you are powering the kit via the fuse box, LEDGlow recommends that you
install the wire using LEDGlow’s Add-a-Circuit which is available on LEDUnderbody.com.
c.
For a quick and easy install LEDGlow offers a cigarette lighter attachment that allows you to simply connect the red and black wire to the attachment, then
plug it in to your cigarette lighter for power.
AUTO ON/OFF FUNCTION WITH A SWITCHED SOURCE
This interior lighting kit has the ability to be powered on and off with a switched source, such as the ignition or with the door switch.
To enable this function, simply press and hold the mode button for 3 seconds. When you power the kit on again, it will now be in the
auto on/off mode, which will allow the kit to illuminate when the kit receives a power signal.
To disable this mode, simply turn off the kit and press the sound button for 3 seconds. Once you power the kit back on, only the on/off
button will allow the kit to turn on.
ON/OFF Button
This button will power the kit on and off
Mode Button
This button allows you to select from 7 solid color modes and 8
Unique Patterns
Sound Button
This button will put the kit into sound activation mode
NOTE: Use the wheel that is located on the side of the control
box to finely tune the sensitivity of the sound activation mode
MODES:
Slow Color Fade
LED Color Pause
Intermediate Color Fade
Fast Color Fade
Slow Ascending Color Fade
Intermediate Ascending Color Fade
Fast Ascending Color Fade
Fast Color Scan
Solid Red Illumination
Solid Green Illumination
Solid Blue Illumination
Solid Yellow Illumination
Solid Purple Illumination
Solid Teal Illumination
Solid White Illumination
For accessories, replacement parts and/or technical support please visit
or more information.