LEDGlow 2pc Interior LED Lighting Starter Kit User Manual
2pc expandable led interior starter kit
2pc Expandable LED Interior Starter Kit
Warning:
Please check your state and local laws before installing this LED interior lighting kit. Every state has different policies and procedures in place regarding
aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while using this interior kit. This kit is for off road use only.
Warning:
The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties. The
control box that is used to power the interior tubes must be installed in a dry location! Having this part exposed to water or the elements will cause the kit’s
controller to fail. Any water damage or corrosion to this part will VOID all warranties.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED INTERIOR KIT.
Interior Kit Includes:
(2) 9 Inch Tubes
(1) Control Box w/ Junction
Cable
(8) Screws
(4) Mounting Brackets
3M Tape
Interior Kit Installation:
1.
Arrange the interior tubes where you plan on installing them and temporarily power the kit to ensure proper functionality before installing. Once you
test the kit and determine it is functioning properly, disconnect the power from the kit and begin the installation.
2.
Mount the first tube to your desired location with the included screws. If you do not want to use the supplied screws, you can use 3M tape, wire ties, or
even Velcro. Make sure the tube and the lead power wire do not come in contact with any moving parts such as the pedals, steering column, and/or seat
tracks.
3.
Mount the other tube to your desired location in the same way you did in the previous step. Again, be sure the tube and lead power wire is not in the
way of any moving parts such as the pedals, steering column, and/or seat tracks.
4.
Connect the tubes to the Junction Cable and mount the Control Box in a readily accessible area using the supplied 3M tape.
Warning: Be sure to mount the Control Box and Junction Cable in a moisture and heat free area. Any damage to your kit as a result of
moisture or heat will void your warranty.
5.
Now, that your Control Box and tubes are mounted, secure and hide all of the lead wires.
6.
This interior kit can be powered one of four ways.
Connect the red power wire to any positive (+) 12 volt source and the black wire to a bare metal ground source. If you need to extend the power
wires, be sure to only use 16 or 18 gauge automotive grade wire. If you are running the power wire to the battery, it must go through the firewall
by using an existing grommet or by drilling a hole and adding a new grommet, which is available at any auto parts store. Be sure to install the
fuse within 6 inches of the power source. If you connect the power wire to a switched 12 volt source, the interior kit may not remember the color
and pattern it was last on before turning off the vehicle. If you connect the power wire to a constant 12 volt source, the interior kit will remember
the last color and pattern it was on prior to turning the vehicle off. Do not run the wire through the door jam, the wire can be pinched and
the will void all warranties.
This interior kit can also be powered directly from your vehicle’s fuse box by using LEDGlow’s Expandable Circuit, which is available at
r at any auto parts store.
For a quick and easy install, LEDGlow offers a Cigarette Lighter Adapter that allows you to simply connect the red and black wires to the lighter
attachment and plugging it into your cigarette lighter for power. This accessory is available on
AUTO ON/OFF FUNCTION WITH A SWITCHED SOURCE
i. This interior lighting kit has the ability to be powered ON and OFFF with a switched source, such as the ignition or with the door
switch.
ii. To enable this function, simply press and hold the mode button for 3 seconds. When you power the kit ON again, it will now be in
the auto ON/OFF mode, which will allow the kit to illuminate when the kit receives a power signal.
iii. To disable this mode, simply turn OFF the kit and press the sound button for 3 seconds. Once you power the kit back ON, only the
ON/OFF button will allow the kit to turn ON.