LEDGlow Million Color Pro SMD LED Interior Lighting Kit - Manual

Million Color Pro Expandable Interior Lighting Kit
Warning: Please check your state and local laws before installing the kit. Every state has different policies and procedures for aftermarket accessories. LEDGlow is not responsible for any fines that you may receive while
using the interior kit. This kit is for off road use only.
Warning: LEDGlow recommends this kit is installed by a licensed professional. Any damage to this kit that is the result of improper installation will void all warranties.
The Control Box must be installed in a dry location! Having this part exposed to water or the elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will VOID all warranties.
Please read the following instructions thoroughly before installing your kit.
1. Arrange the tubes the way you plan to install them on the interior of the vehicle, and test the kit to ensure it is properly functioning before installing.
2. Remove any trim pieces from the interior of your vehicle that may hinder the installation of the tubes. (Optional)
3. Starting with the front tubes, mount them with plenty of clearance from any moving parts such as the steering shaft and pedals. Make sure the wires are not close to the seat tracks or anything that may
potentially cut or pinch the wires.
NOTE: Output A and Output B located on the side of the control box are used to power the LED interior tubes. Use one or both of the outputs to power your kit. Both of them do not have
to both be used.
4. Each interior tube can be mounted virtually anywhere in your vehicle. Some good locations are under the dash in the foot well area, under the driver and passenger seats facing the foot well area, under
the back of the driver and passenger seats facing in the back seat, or even in the trunk.
5. Find a safe, secure, and dry position to mount the control box. We recommend mounting the control box in your center console, under the seat, or in your glove box.
6. Connect the red wire to any 12 volt source. If you need to extend the power wires, be sure to only use a 14 or 16 gauge automotive grade wire. If you are connecting the red wire directly to your
battery, you must go through the fire wall. You need to protect the wire by using an existing grommet or by drilling a hole and adding a new grommet which is available at any auto parts store, and be
sure to install a fuse within 6 inches of the power source. (Fuse is not included if you have to extend the power wire.) If you connect the red wire to a switched 12v source it may not remember the
color and pattern your kit was on before the vehicle was powered off. You can avoid this problem by connecting the power wire to a constant 12 volt source. The kit will stay on until you turn it off
if it is connected to a constant 12 volt source. If you are powering your kit through the fuse block, LEDGlow recommends that you install the power wire using our add-a-circuit which is available
online at
www.LEDGlow.com .
7. Connect the black ground wire to any good ground source on your vehicle. You can connect this wire directly to the battery or any engine ground.
8. DO NOT SHORTEN OR CUT ANY OF THE USB POWER WIRES. This will destroy the kit and void the warranty. LEDGlow offers 1, 3, 5, and 9 foot Mini USB power wires if you need a
longer wire to mount your interior tubes.
9. If you removed any interior trim for this light kit installation you can now reinstall them and test the functionality of your cut.
WARNING: DO NOT TURN ON OR CONNECT POWER TO THE CONTROL BOX
UNTIL ALL TUBES ARE PROPERLY CONNECTED
Controller Operation
 Button A: Power On/Off (Press and Hold for 3 Seconds)
o During operation press this button once to pause the current color changing function. Press it a second time to continue with the color change function.
 Button B: Modes
 Million color change (Color change option is not available on this mode)
 Fade
 Solid illumination (Speed Function is not available on this mode)
 18 - Color change (Color change is option is not available on this mode)
 Single Color Flashing
 18 -Color Flashing (Color change option is not available on this mode)
 SOS Flashing (Speed function and music mode is not available on this mode)
 Demo (Changes thought the above functions every 15 seconds.)

Button C: Color Change mode
 Blue  Light Yellow
 Red  Lime Green
 Green  Violet
 Pink  Ice Blue
 White  Teal
 Yellow  Deep Blue
 Purple  Pale Green
 Orange  Hot Pink
 Light Purple  Dark Purple
 Button D: Speed Function / Music mode
o There are 5 speed levels
o Music mode
 Press and hold the button for 3 seconds to activate music mode. (You will hear one beep when activating music mode)
 Press and hold the button for 3 seconds to deactivate music mode. (You will hear two beeps when deactivating music mode)
Reprogramming the Wireless Remote
1. Turn the kit off
2. Press and hold any button on the wireless remote. While holding the button down on the remote press the B button on the control box
3. If the sync was successful you will hear one beep, if it was not successful you will hear multiple beeps
4. If the sync was not successful repeat steps one and two. If you are having continued problems please contact our technical support department at 1.856.768.5700
Expandability Options
 This 4pc Million Color SMD-LED Expandable Interior Lighting Kit can be expanded to power a total of 72 SMD LEDs.
 This control box can power an additional 4 SMD LED Interior Lighting Tubes.
For accessories, replacement parts, and / or technical support please visit www.LEDGlow.com for more information.