Watlow EZ-ZONE ST - Manual (Page 11)

Watlow EZ-ZONE ® ST • 9 • Chapter 2 Install and Wire
–
+ –
+ –
+
S1 S2
S3
S1 S3
– +
Thermocouple
(Input 2)
Process
0 to 20 mA
(Input 2)
N.O. (Output 3)
N.C. (Output 3)
common (Output 3)
N.O. (Output 4)
contactor (Coil 1)
Contactor
Coil 1
Contactor
Coil 2
ST_ B - _ _ _ _ - _ _ _ _ (no limit)
ST_ L - _ _ _ _ - _ _ _ _ (with limit)
common (R
UI)
T-/R- (R
UI)
T+/R+ (R
UI)
- common (Digital I/O) + Digital Input 6 or Output 6 + Digital Input 5 or Output 5
ST_ _ - _ _ A _ - _ _ _ _
Remote User Interface (RUI)
common (Modb
us R
TU)
T-/R- (Modb
us R
TU)
T+/R+ (Modb
us R
TU)
- common (Digital I/O) + Digital Input 6 or Output 6 + Digital Input 5 or Output 5
ST_ _ - _ _ M _ - _ _ _ _
Modbus RTU on EIA-485
Limit
Address
Selection
fuse
load
S1 S2
S3
+ –
S1 S3
2-wire
RTD
(Input 1)
3-wire
RTD
(Input 1)
Thermocouple
(Input 1)
Process
0 to 20 mA
(Input 1)
Process
0 to 10V Î (dc)
0 to 50mV Î (dc)
(Input 1)
N.O.
(Output 2)
common
(Output 2)
Controller
– +
2-wire
RTD
(Input 2)
3-wire
RTD
(Input 2)
98 99 CF CD CE B5 D6 D5
L2 K2 T1 S1 R1 L2 K2 T1 S1 R1
98 99 CC C
A
CB B5 D6 D5
1 2 3 4
ON
L3 K3 J3 A1 L4 T2 S2 R2
L2 K2 T1 S1 R1
L2 K2 T1 S1 R1
L2 K2 T1 S1 R1
L2 K2 T1 S1 R1
L3 K3 J3 A1 L4 T2 S2 R2
L3 K3 J3 A1 L4 T2 S2 R2
L3 K3 J3 A1 L4 T2 S2 R2
L3 K3 J3 A1 L4 T2 S2 R2
neutral hot
fuse fuse
earth
ground
1
6 3
4
A1 A2
2 5
EZ-ZONE™ ST
Patent Pending
Integrated
Control Loop
1 2 3 4
ON
L
IM
IT
O
U
T
3
S
S
R
S
TA
T
U
S
O
U
T
2
L
IM
IT
O
U
T
3
S
S
R
S
TA
T
U
S
O
U
T
2
hot hot
Process
0 to 10V Î (dc)
0 to 50mV Î (dc)
(Input 2)
Power Supply
Power Supply
fuse
fuse
Output 1 (SSR)
Wiring
with a contactor (ST _ _ - (B or F) _ _ _ - _ _ _ _)
Ó
WARNING: Use National Electric
(NEC) or other country-specific
standard wiring and safety prac-
tices when wiring and connecting
this controller to a power source
and to electrical sensors or pe-
ripheral devices . Failure to do so
may result in damage to equip-
ment and property, and/or injury
or loss of life .
ç
WARNING: If high voltage is applied to a
low-voltage controller, irreversible damage
will occur .
Note:
Terminals L4 and A1 on the limit connector
are jumpered at the factory to complete the
contactor circuit . Additional switches may
be wired in series to the terminals .
Note:
Use the contactor with a minimum load of
100 watts .
STATUS Indicator Light
Flashing green indicates the controller is run-
ning with no input errors .
Flashing red indicates an input error .
No flashing indicates that the controller is not
functioning .
CAUTION: Always mount the controller as
shown, with the heat-sink fins aligned verti-
cally .
Note:
The control common terminal and the digital
common terminal are referenced to different
voltages and must remain isolated .
Note:
A2 is connected internally to terminal 98 .
A1 is connected internally to the contac-
tor coil . The other side of the coil is con-
nected to terminal 99 .