Vaddio AutoTrak 2.0 - Manual (Page 4)

AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 4 of 52
Intended Use:
Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested for
use indoors, and with the provided power supply and cabling. The use of a power supply other than the one provided
or outdoor operation has not been tested and could damage the device and/or create a potentially unsafe operating
condition.
Important Safeguards:
Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged. In
this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock, do
not immerse in water or other liquids and avoid extremely humid conditions.
Save These Instructions:
The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product drawings
for the Vaddio product line on the Vaddio website. These documents can be downloaded from
www.vaddio.com free.
UNPACKING:
Carefully remove all of the parts for the AutoTrak 2.0 999-7250-000 Dual HD-18 Kit with Quick Connect DVI/HDMI Interface (North
America Only) packaging:
 One (1) AutoTrak 2.0 CPU (closed system preloaded with AutoTrak 2.0 software and video card)

One (1) AC Cord Set for AutoTrak 2.0 CPU
 One (1) PS/2 Keyboard and PS/2 Mouse
 One (1) IR and Audio Lanyard with attached cable with 5-pin mini XLR connector,
 One (1) Audio-Technica AT8439 Cable Clip to attach Lanyard Central Medallion to clothing

One (1) Triple Circle Magnet Kit for attaching the Lanyard Central Medallion to clothing from the inside
 One (1) Belt Pack Unit “BPU” with 1” (1/4 wave) RP-SMA straight antenna and attached belt clip with rechargeable lithium-ion
battery pack and 5 VDC USB charging power supply for North America

One (1) USB Type A-Male to micro-B-Male Charging Cable
 One (1) Vaddio PowerRite 12 VDC, 1A Switching Power Supply with North American Power Cord
 One (1) AutoTrak POD Kit (for presets and rescan) and Manual (in separate box)
AutoTrak 2.0-Dual HD-18 Kit:

One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
 One (1) Quick-Connect DVI/HDMI SR Interface (998-1105-018) for Tracking Camera
 One (1) 24VDC, 2A, Switching Power Supply with North American Power Cord
 One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded – IR Reference Camera

One (1) 37mm female lens ring adapter, One (1) 37mm to 58mm adapter ring, One (1) 58mm polarizing filter, One (1) 58mm
band-pass IR filter, all parts adapters and filters attached to HD-18 Camera
 One (1) AutoTrak 2.0 Quick-Connect Box (998-1105-020)

One (1) Standard Quick-Connect Box (998-1105-001)

One (1) 24VDC, 2A, Switching Power Supply with North American Power Cord
 One (1) 18”/45.8cm Video Cable (BNC to RCA)
 One (1) 12”/30.48cm Cat 5e Patch Cable
 One (1) 998-2100-000 - Vaddio IR Remote & Manual (2-AAA batteries not included)

One (1) **535-2000-233 Stacked Dual Mount for two cameras and Mounting Hardware
 Three (3) 998-1001-232 Control Adapters
 One (1) 998-7200-232 Control Adapter for use with the AutoPresenter - (Only needed when used with the AutoPresenter for
Tracking Camera PTZ Presets)

One (1) AutoTrak Pod Kit 998-7200-110 (for presets and rescan) and Manual (in separate box)
 Documentation and Manuals (Document Number (342-0382)
For the 999-7260-000 System¨ Start with the 999-7250-000 System
Remove: One (1) *AutoTrak HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
Add: One (1) *AutoTrak HD-20 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
Use only the power supply provided with the system. Use of any unauthorized power
supply will void any and all warranties.
Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not
work well for professional installations and can be the cause of intermittent connections which
can result in the RS-232 control line failing and locking up, and/or compromising the HSDS™
signals. For best results please use standard RJ-45 connectors and test all cables for proper
pin-outs prior to use and connection to Vaddio product.
The AutoTrak 2.0 CPU is a computer running a Linux OS. Please do not
remove power from the AutoTrak 2.0 CPU without first shutting the system
down, as you would any other business computer. Only after the AutoTrak
2.0 CPU has been shut down, it is safe to remove power. Consistently power
cycling the CPU with the Rear Power Switch may cause the system to load
improperly, which could potentially result in data errors requiring factory
service.
Please treat the AutoTrak 2.0
CPU like a computer.
Please shut down
the CPU before
removing power,
like all business
computers, or…