Kpm iii monitor operation – Kinze 3110 Mounted Planter Rev. 7/14 User Manual

Page 78

Advertising
background image

M0244-01

Model 3110

5-4

9/12

TM

KPM III Monitor Operation

KPM III Monitor Operation

STEP 3

Select ‘‘5. Configure Planter Monitor’’ by turning the

knob or using the arrow keys. Press the knob or the

Enter key to display the highlighted item.

NOTE: Press F2 key next to Plant any time Plant option is

available to return to Planter Configuration screen.

NOTE: Planter monitor cannot be reconfigured while planting.

STEP 4

If there are front rows (Interplant) on planter, press

knob or Enter key to highlight “Front Rows” field. A

drop down number pad appears. Turn knob or use

arrow keys to highlight correct value then press tknob

to select number. For numbers containing more than

one digit select one digit at a time. When desired

quantity is displayed above number pad press Enter

key to return to “Kinze Planter Configuration” screen.

If planter has no front rows turn knob or press arrow

keys to advance to “Rear Rows”.

Status

Plant

About

Setup Mode

Configuration:

Effective row spacing: 15.0

Front / Rear

1. General Settings

2. Seed Meter Settings

3. Row Unit Alarm Levels

4. Setup Data Logging

5. Configure Planter Monitor

6. Add New Muxbus Sensors

7. Add Single Interplant Row

8. Select Speed Sensor

9. Sensor Setup

10.Calibrate Speed Sensor

Logdata

SDS = Seed Delivery System

There should be one sensor

for each Row and each Shaft.

Cancel

Kinze Planter Configuration

Planter Type

Sensors Installed

Front Rows

0

OK

Rear Rows

12

Shafts

2

0

Speed

Radar

Vacuum

0

SDS

Hydraulic Level/Temp

0

Downpressure Level

1 2 3

C

4 5 6
7 8 9

.

0

-

STEP 5

Press knob or Enter key to select “Rear Rows” field.

A drop down number pad appears. Turn knob or use

arrow keys to highlight correct value then press knob

to select number. For numbers containing more than

one digit select one digit at a time. When desired

quantity is displayed above number pad, press

Enter key to return to “Kinze Planter Configuration”

screen.

STEP 6

Rotate knob or use arrow keys to advance to “Shafts”

field. Press knob or Enter key to select “Shaft” field.

A drop down menu appears. Turn knob or use arrow

keys to highlight number of “Shafts”. When correct

value is displayed, press knob or Enter key to return

to “Kinze Planter Configuration” screen.

STEP 7

Turn knob or use arrow keys to move to “Speed”

field. Press knob or Enter key and a drop down

menu displays. Select ‘‘Radar’’ or ‘‘Coil Pick-Up’’

(MDS) by turning knob or using arrow keys. When

desired selection is highlighted press knob or Enter

key.

SDS = Seed Delivery System

There should be one sensor

for each Row and each Shaft.

Cancel

Kinze Planter Configuration

Planter Type

Sensors Installed

Front Rows

0

OK

Rear Rows

11

Shafts

2

0

Speed

Radar

Vacuum

0

SDS

Hydraulic Level/Temp

0

Downpressure Level

1 2 3

C

4 5 6
7 8 9

.

0

-

SDS = Seed Delivery System

There should be one sensor

for each Row and each Shaft.

Cancel

Kinze Planter Configuration

Planter Type

Sensors Installed

Front Rows

11

OK

Rear Rows

12

Shafts

2

0

1

2

4

Speed

Radar

Vacuum

0

SDS

Hydraulic Level/Temp

0

Downpressure Level

SDS = Seed Delivery System

There should be one sensor

for each Row and each Shaft.

Cancel

Kinze Planter Configuration

Planter Type

Sensors Installed

Front Rows

11

OK

Rear Rows

12

Shafts

2

2

Speed

Vacuum

0

SDS

Hydraulic Level/Temp

0

Downpressure Level

Radar

Radar

Coil Pick-Up

Advertising