Rockwell Automation 160-DN2 160-DN2 DeviceNet Communication Module FRN 3.xx - Manual (Page 36)

Publication 0160-5.18 - June 2003
5-8 DeviceNet Parameter Descriptions
Drive Program Parameters Below is a brief description of the Bulletin 160 SSC Interface
Program Group parameters. Refer to the Bulletin 160 SSC User
Manual for more detailed information on these parameters.
Parameter
Number
Parameter Name
Object Mapping
(Class-Instance-
Attribute)
Description Units
30 [Accel Time 1] 0xB3-1-30 Time to ramp from 0 Hz to maximum frequency. 0.1 Seconds
31 [Decel Time 1] 0xB3-1-31 Time to ramp from maximum frequency to 0 Hz. 0.1 Seconds
32 [Minimum Frequency] 0xB3-1-32 Lowest continuous output frequency. 1 Hz
33 [Maximum Frequency] 0xB3-1-33 Highest continuous output frequency. 1 Hz
34 [Stop Mode Select] 0xB3-1-34 Determines stop mode used. Numeric Value
35 [Base Frequency] 0xB3-1-35 Set to motor’s nameplate frequency. 1 Hz
36 [Base Voltage] 0xB3-1-36 Set to motor’s nameplate voltage. 1 Volt
37 [Maximum Voltage] 0xB3-1-37 Highest voltage the drive will output. 1 Volt
38 [Boost Select] 0xB3-1-38 Sets the volts/Hz relationship. Numeric Value
39 [Skip Frequency] 0xB3-1-39 Frequency at which drive will not run continuously. 1 Hz
40 [Skip Freq Band] 0xB3-1-40 Used with P39 - [Skip Frequency] to create skip band. 1 Hz
41 [Overload Select] 0xB3-1-41 Selects derating factor for motor overload. Numeric Value
42 [Motor Overload] 0xB3-1-42 Set to motor nameplate full load amperes. 0.01 Amperes
43 [Current Limit] 0xB3-1-43 Max output current allowed before limiting. % I rating
44 [DC Hold Time] 0xB3-1-44 DC Injection Braking duration. 0.1 Seconds
45 [DC Hold Voltage] 0xB3-1-45 Voltage level for DC Injection Braking. 1 Volt
46 [Input Mode] 0xB3-1-46 Type of START, STOP, REV, commands. Numeric Value
47 [Output Configure] 0xB3-1-47 Configures TB3 output relay functionality. Numeric Value
48 [Output Threshold] 0xB3-1-48 Used in conjunction with P47 - [Output Configure]. Numeric Value
49 [PWM Frequency] 0xB3-1-49 Carrier frequency for PWM output waveform. 0.1 kHz
50 [Restart Tries] 0xB3-1-50 Times drive will attempt to reset a fault. Numeric Value
51 [Restart Time] 0xB3-1-51 Time between restart attempts. 0.1 Seconds
52 [DB Enable] 0xB3-1-52 Enables/disables dynamic braking. Numeric Value
53 [S-Curve] 0xB3-1-53 Enables a fixed shape S-curve. Numeric Value
!
ATTENTION: Changing this parameter
value may cause unpredictable network
conditions, resulting in equipment damage,
personal injury, or death. Make sure that
you understand how changing this
parameter affects your application.
!
ATTENTION: Changing this parameter
value may cause unpredictable network
conditions, resulting in equipment damage,
personal injury, or death. Make sure that
you understand how changing this
parameter affects your application.