Document Outline

• Computer Numerical Control (CNC) Machining Accelerator Toolkit Quick Start
  • Table of Contents
  • Preface
    • Introduction
    • Conventions
    • Required Software
    • Additional Resources
      • Additional Toolkits and FANUC Publications
  • 1 - Architecture and Hardware Selection
    • Before You Begin
    • What You Need
    • Follow These Steps
    • Review System Selection and Configuration Tools
      • FANUC CNC Express Software
      • Rockwell Automation DMAT Wizard Software
      • Rockwell Automation Safety Selection Tools
      • Rockwell Automation Product Selection Toolbox
    • Open FANUC CNC Express Software
    • Create CNC System Bill of Materials
    • Create Supervisory Controller and Safety System Bill of Materials
  • 2 - System Layout and Wiring
    • Before You Begin
    • What You Need
    • Follow These Steps
    • Select FANUC CNC Drawings from Drawing Library
    • Edit FANUC CNC Drawing Set
      • Create a New Project
      • Edit CNC Power Drawings
      • Edit CNC Safety and Standard I/O Drawings
      • Edit System Communication Drawings
      • Edit CNC System Layout Drawing
    • Assemble and Edit Your GuardLogix System Drawing Set
  • 3 - FANUC CNC Configuration
    • Before You Begin
    • What You Need
    • Follow These Steps
    • Initial FANUC CNC Configuration
      • System Powerup
      • Parameter Write Enable
      • High Speed Ethernet Option
      • Configure Ethernet Module
        • IP Address, Subnet Mask, and Port Number
      • Create a New Project File
      • Download FANUC LADDER III Software Project to the FANUC S35i-B CNC
      • USB External Device
      • EtherNet/IP Settings
    • Logic Configuration
      • Editing Application Logic Modules and Adding Code
        • P0001 (OP Panel Path 1)
        • P0005 (Machine Sequence)
        • P0010 (Window Functions)
        • P0023 (Alarm Routine)
      • Device Logic Modules
        • P00015 (PLC EIP Input Routine)
        • P00016 (PLC EIP Output Routine)
      • Verify and Save the Project File
      • Download FANUC LADDER III Software Project to the FANUC S35i-B CNC
  • 4 - GuardLogix Configuration
    • Before You Begin
    • What You Need
    • Follow These Steps
    • Create an Initial GuardLogix Project Using the DMAT Wizard
      • Order and Run the DMAT Wizard
      • Import the Preconfigured RSLogix 5000 Project
    • GuardLogix Controller and Network Configuration
      • Create a New Project File
      • Configure Ethernet Module for your HMI Terminal and CNC Modules
      • Save the Project File
    • Import and Configure the Machine Logic Module
    • FANUC CNC AOP Configuration
      • Update FANUC CNC Add-On Profile (AOP)
      • Add and Configure FANUC CNC
    • Save the Project File
    • Import and Configure CNC Application Logic Module
    • Import and Configure FANUC CNC Device Logic Modules
    • Set String Tag Names for Alarm History Faceplate
    • Set Visible Rows for Equipment Status Faceplate
    • Import and Configure Device and Application Status Logic
    • Create Specific Application Logic
      • Application Code Logic Template Overview
      • Application Logic Creation Steps That Use Application Logic Examples
        • Toolkit Application Logic Example Overview
        • CNC Work Cell Logic Example Overview
        • Import Application Logic Examples
      • Application Logic Creation Steps That Use a Template
    • Safety Logic Integration
      • Safety I/O
      • GuardLogix Safety Logic
      • Safety Faceplate Logic
    • Verify and Save the Project File
  • 5 - FactoryTalk View ME Configuration
    • Before You Begin
    • What You Need
    • Follow These Steps
    • Design from a Preconfigured HMI Application File
      • Restore and Open a Preconfigured HMI Application
      • Delete Unused Displays
      • Delete Unused Parameter Files
      • Configure Parameter Files
      • Delete Unused Alarm Triggers and Tags
    • Design from an Existing HMI Application File
      • Open Your Existing HMI Application File and Add Displays
      • Add Parameter Files
      • Configure Parameter Files
      • Import Alarm Setup File
      • Delete Unused Alarm Triggers
      • Import and Edit Alarm Tags
    • Configure Goto Display Buttons on Startup Display
      • Add FANUC CNC Goto Buttons to Your Application
      • Associate Each Button to a Faceplate and Parameter File
    • Configure Equipment Status Faceplate Display
      • Add the Equipment Status Faceplate Display
      • Add the ME_Equipment_Parameter File
      • Configure Goto Buttons on the Equipment Status Faceplate
      • Configure Additional Device Value Columns
    • Configure Safety Faceplate Displays
  • 6 - System Commissioning
    • Before You Begin
    • What You Need
    • Follow These Steps
    • Download Applications
      • Download RSLogix 5000 Software Project File to the Logix Controller
      • Configure and Download FactoryTalk Project to PanelView Plus Terminal
        • Create a New RSLinx Enterprise Configuration
        • Configure Design (Local) Communication
        • Configure Runtime (Target) Communication
        • Create Your FactoryTalk View Runtime Application File
        • Download Runtime File to PanelView Plus Terminal
    • Commissioning Devices
      • Commissioning CIP Motion Drives
      • Commissioning sercos Drives
      • Commissioning PowerFlex 7-class Drives
      • Commissioning PowerFlex 4-class Drives
      • Commissioning Kinetix 300 Drives
    • Commissioning Supervisory and CNC System
      • Verify Network Communication
        • HMI Terminal to Logix Controller Communication
        • Controller to Device Communication
        • CNC to Controller Communication
      • Clearing Faults
        • HMI Clear Faults
        • HMI Test Faults
      • Operator (manual) Control
      • Program (automatic) Control
  • 7 - System Application Guide
    • Before You Begin
    • What You Need
    • Follow These Steps
    • Machine Startup Faceplate
      • Machine Status
      • Machine Control
      • Program/Operator Mode
      • State Diagram Faceplate Display
    • CNC Faceplate
      • Home View
      • CNC Status Views
      • CNC Control Views
      • Fault Indication View
      • Fault Diagnostic Views
      • Configuration View
      • Online Help Views
    • Motion Drive and/or PowerFlex Drive Faceplates
    • Guard I/O Safety Faceplates
    • Equipment Status Display Overview
    • Alarm History Display Overview
  • A - Logic Program Overview
    • Machine/Application/Device Module Relationship
    • Module Routine Overview
      • Machine Module
        • Machine States
        • Machine Control Module Tags
        • Device and Application Status Rung Tags and Logic
      • Application Modules
      • Device Modules
        • Device Module Tags
        • Device Module Control Logic Example
  • B - Logic Module Customization
    • Machine State Customization
      • Tag and Logic Modification Recommendations
      • State Display Tag Modifications
      • Bypass Idle State Modifications
    • Module Fault Customization
    • Alarm History Faceplate Logic Modification
    • Coordinated Reset Customization
  • C - Add Other Devices to the Equipment Status Faceplate
    • Add Devices to the Equipment Status Faceplate
    • Add Optional Faceplate Views
  • D - Logix Communication and Controller Configuration
    • Configure Personal Computer Communication Properties
      • Set the IP Address
      • Verify Your IP Address
    • Configure the EtherNet/IP Driver
    • Configure the Logix Controller
      • Check the Web for ControlFLASH Firmware Updates
      • Load the Controller Firmware
      • Assign IP Addresses
      • Browse the EtherNet/IP Network Devices
  • Index
• Back Cover