Banner Q60 Background Suppression Series - Manual (Page 7)

page 7
Q60V Series Adjustable-Field Sensors –
Visible Red Emitter
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Q60V Specifications
Sensing Hysteresis
Output Rating Q60BB6AFV models
150 mA maximum each output @ 25° C
Off-state leakage current: < 5µA @ 30V dc
Output saturation NPN: < 200 mV @ 10 mA and < 1V @150mA
Output saturation PNP: < 1V at 10 mA; < 1.5V at 150 mA
Q60VR3AFV Universal models
Min. voltage and current: 5V dc, 10 mA
Mechanical life of relay: 50,000,000 operations
Electrical life of relay at full resistive load: 100,000 operations
Max. switching power (resistive load):
Cabled models: 1250VA, 150 W QD models: 750VA, 90W
Max. switching voltage (resistive load): Cabled models: 250V ac, 125V dc QD models: 250V ac, 125V dc
Max. switching current (resistive load):
Cabled models: 5 A @ 250V ac, 5 A @ 30V dc derated to 200 mA @ 125V dc
QD models: 3 A @ 250V ac, 3 A @ 30V dc derated to 200 mA @ 125V dc
Output Protection Circuitry Q60BB6AFV models: Protected against continuous overload or short circuit of outputs
All models: Protected against false pulse on power-up
Output Response Time
Repeatability 500 microseconds
See Figure 12.
Construction Housing: ABS polycarbonate blend Lens: Acrylic Cover: Clear ABS
Environmental Rating IEC IP67; NEMA 6
Connections 2 m (6.5') or 9 m (30') attached cable, 5-pin Euro-style fitting, or 5-pin Mini-style 150 mm (6") QD pigtail,
depending on model. QD cables are ordered separately; see page 8.
Operating Conditions Temperature: -20° to +55°C (-7° to +131°F)
Maximum Relative Humidity: 90% at 50°C (non-condensing)
Indicators
NOTE: Outputs are active
during on/off timing
selection mode.
ON Delay Steady Green: Run mode, ON delay is active
Flashing Green: ON Delay Selection mode is active
OFF Delay Steady Green: Run mode, OFF delay is active
Flashing Green: OFF Delay Selection mode is active
5-Segment Light Bar*: Indicates relative delay time during ON or OFF Delay Selection modes
Output Steady Amber: Outputs are conducting
Steady Green: During ON/OFF Delay Selection modes
Dark Operate Steady Green: Dark Operate is selected
Lockout Steady Green: Buttons are locked out
Light Operate Steady Green: Light Operate is selected
Signal Steady Green: Sensor is receiving signal
Flashing Green: Marginal signal (1.0 to 2.25 excess gain)
*Output, Dark Operate, Lockout, Light Operate and Signal indicators function as 5-Segment Light Bar during
ON or OFF Delay Selection modes
Adjustments 2 momentary push buttons: ON Delay (+) and OFF Delay (–) (DC models also have remote program wire)
ON Delay select: 8 ms to 16 seconds
OFF Delay select: 8 ms to 16 seconds
LO/DO select
Push button lockout for security
Slotted, geared, 2-turn, cutoff range adjustment screw (mechanical stops on both ends of travel)
Q60BB6AFV models: 2 milliseconds ON and OFF
NOTE: 150 millisecond delay on power-up; outputs do not conduct during this time.
Q60VR3AFV Universal models: 15 milliseconds ON and OFF
NOTE: 150 millisecond delay on power-up; relay is de-energized during this time.
Certifications