R58 expert, Registration mark sensors, Setup configuration – Banner R58 Registration Mark Sensors User Manual
Page 7: Procedure result push button, Remote line, Enter setup mode, Select lo/do and delay settings (see figure 4), Lo/do setting shortcut, Enable/disable sensing beam colors (see figure 5), Return to setup/run mode
P/N 122928 rev. C
7
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
R58
Expert
™
Registration Mark Sensors
SETUP Configuration
* If the new color setting has only one sensing beam color enabled, the sensor will switch to that color for sensing.
If the new color setting has multiple sensing beam colors enabled, the sensor will use the color that was active prior to configuration; following the next TEACH procedure, it will
select the enabled sensing beam color that has the greatest contrast.
Procedure
Result
Push Button
0.04 sec. ≤ “click” ≤ 0.8 sec.
Remote Line
0.04 sec. ≤ “T” ≤ 0.8 sec.
Enter
SETUP
Mode
• Press and hold both
push buttons
> 2 seconds.
• Double-pulse the remote line.
• 8-Segment display turns OFF.
• Sensor is in SETUP mode.
Select
LO/DO
and
Delay
Settings
(see
Figure
4)
• Release push buttons.
• Wait > 8 seconds.
• Sensor is ready to select a new setting
combination.
• Click Static (–) or Dynamic (+)
push button to toggle between
choices:Dynamic (+) — increment
Static (–) — decrement
• Enter sequential pulses to toggle
between choices:
Single-pulse — increment
Double-pulse — decrement
• Sensor steps between LO/DO and Delay setting
combinations, as shown in Figure 4.
LO/DO
Setting
Shortcut
• Not available using push buttons.
• From RUN mode, three-pulse the
remote line.
• Sensor toggles between LO/DO settings
on-the-fly, and continues in RUN mode.
Enter
Sensing
Beam
Color
Select
Mode
(from
SETUP
Mode)
• From SETUP mode, press and hold
Dynamic (+) push button > 2 seconds.
• From SETUP mode, four-pulse the
remote line.
• Sensor displays currently selected sensing beam
color combinations, as shown in
Figure 5.
• Visible sensing beam also provides indication of
enabled sensing beam color(s).
Enable/Disable
Sensing
Beam
Colors
(see
Figure
5)
• Click Static (–) or Dynamic (+)
push button to toggle between
choices:Dynamic (+) — increment
Static (–) — decrement
• Enter sequential pulses to toggle
between choices:
Single-click — increment
Double-click — decrement
• Sensor steps between possible sensing beam
color combinations, as shown in Figure 5.*
• Visible sensing beam also provides indication of
enabled sensing beam color(s).
Return
to
SETUP/RUN
Mode
• Press and hold
Static (–) push button
> 2 seconds to return
to SETUP mode.
• Four-pulse the remote line to return to
SETUP mode.
• Sensor returns to RUN mode with new settings.
• These steps will return to RUN mode from both
SETUP modes.
• Then press and hold
both push buttons
> 2 seconds to
return to RUN mode.
• Hold the remote line low > 2 seconds to
return to RUN mode.
• Or wait > 60 seconds.
• Or wait > 60 seconds.
or
T
T T T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
or
or
or
T
T T T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T