To stop recording, To check the order, To cancel time edit – Sony LBT-D670AV User Manual
Page 17: To select the desired tracks beforehand
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
1
Press FUNCTION repeatedly until
"CD" appears in the display.
2
Press = OPEN and load a CD on the
tray.
Make sure the disc number in the
playing position in the display is the one
you want to record.
The total number of tracks and the
playing time appear in the display.
3
Press = EJECT and insert a blank tape
into deck B with the side you want to
record on facing forward.
Recording starts from the front side of
the tape, unless you change the playing
direction before recording.
Make sure the tabs on the cassette have
not been removed.
4
Select dual or single sided recording.
To record
Press DIRECTION to
select
One side
Both sides*
cn3 or RELAY
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
5
When you want to reduce the hiss noise
in low-level high-frequency signals,
press DOLBY NR so that "DOLBY NR
B" appears in the display.
6
Press EDIT twice.
"TIME EDIT" then "SELECT" and
"TIME" appear alternately in the '
display.
7
Press
on the remote to
designate the tape length or "HALF".
As you press the button, the display
changes as follows:
- C.46 -■
(23,00)
- C-54 -
(27 00)
• C-90 -
(45.00)
. C-74 .«■ C-60 »
(37 00)
(30.00)
Choose "HALF" if you want the CD
player to record half of the total playing
time of the CD in the original order. You
cannot select "HALF" when recording
CDs with more than 20 tracks.
"PUSH EDIT" and half of the total time
of the tape you selected appears in the
display.
Half of the total time of the tape
8
Press EDIT on the remote.
The CD player determines the tracks to
be recorded on side A automatically.
The total time and tracks to be recorded
on side A appears in the display.
Tracks to be recorded on side A
1
I’ll jjj
Total playing time on side A
9
When you want to record on both sides,
press EDIT again. The CD player
determines the tracks to be recorded on
side B.
Tracks to be recorded on both sides
ta>l 1
Total playing time on side B
10
Press CD SYNCHRO.
The REC and DD (pause) lamps light up
and deck B stands by for recording.
The O lamp lights up and the O lamp
flashes for a few seconds, then goes off.
1
N
o<3
Side in recording
pause mode
If you want to start recording from the
reverse side, press <l so that the <l
indicator lights steadily.
11
Press 00 on the tape player to release
recording pause.
Recording starts.
After about 10 seconds, the CD player
starts playing.
To Stop recording
Press □ on the tape player.
To check the order
Press CHECK on the remote repeatedly.
Each time you press CHECK, the number of
the programmed tracks appear in the
display.
To cancel time edit
Press CONTINUE on the CD player.
To select the desired tracks
beforehand
You can record certain tracks (up to 20) first
by selecting them before fime editing. See
"Playing Tracks in the Desired Order
(program play)."
Recording a CD:
Specifying
Track
Order (program edit)
You can adjust the total recording time to
the tape length while making a program.
SYSTEM
POWER-4 ON
X
o
Dt_L_Lj r ’----------- ’ ( t* M
□ CONTINUE
1
Following the procedure "Playing
Tracks in the Desired Order (program
play)," program the tracks you want to
record for side A.
Make sure to program the tracks so that
the total playing time of the side A does
not exceed the tape length of one side,
2
Press II on the remote to pause
recording at the end of the side A.
"P" appears in the display.
The total playing time "0.00" appears in
the display.
3
Program the tracks you want to record
for side B in the same way as you did
for side A.
continue to next page ■
Chapter 4: the Tape Player
17