Document Outline

• Revision History
• Imprint
• Disclaimer
• About This Book
  • How to Use This Document
• Proprietary Note
• Trademarks
• Environmental Protection Statement
• Explanation of Symbols
• For Your Safety
  • High Voltage Safety Instructions
  • Special Handling and Unpacking Instructions
  • General Instructions on Usage
• Two Year Warranty
• 1. Using the Command-Line Interface
  • 1.1 Command Syntax
  • 1.2 Command Conventions
  • 1.3 Common Parameter Values
  • 1.4 Slot/Port Naming Convention
  • 1.5 Using the “No” Form of a Command
  • 1.6 FASTPATH Modules
  • 1.7 Command Modes
  • 1.8 Command Completion and Abbreviation
  • 1.9 CLI Error Messages
  • 1.10 CLI Line-Editing Conventions
  • 1.11 Using CLI Help
  • 1.12 Accessing the CLI
• 2. Switching Commands
  • 2.1 Port Configuration Commands
    • 2.1.1 interface
    • 2.1.2 auto-negotiate
      • 2.1.2.1 no auto-negotiate
    • 2.1.3 auto-negotiate all
      • 2.1.3.1 no auto-negotiate all
    • 2.1.4 advertise speed
      • 2.1.4.1 no advertise speed
    • 2.1.5 show advertise speed
    • 2.1.6 block
      • 2.1.6.1 no block
    • 2.1.7 description
    • 2.1.8 mtu
      • 2.1.8.1 no mtu
    • 2.1.9 shutdown
      • 2.1.9.1 no shutdown
    • 2.1.10 shutdown all
      • 2.1.10.1 no shutdown all
    • 2.1.11 speed
    • 2.1.12 speed all
    • 2.1.13 show port
    • 2.1.14 show port protocol
  • 2.2 Spanning Tree Protocol (STP) Commands
    • 2.2.1 spanning-tree
      • 2.2.1.1 no spanning-tree
    • 2.2.2 spanning-tree bpdufilter
      • 2.2.2.1 no spanning-tree bpdufilter
    • 2.2.3 spanning-tree bpdufilter default
      • 2.2.3.1 no spanning-tree bpdufilter default
    • 2.2.4 spanning-tree bpduflood
      • 2.2.4.1 no spanning-tree bpduflood
    • 2.2.5 spanning-tree bpduguard
      • 2.2.5.1 no spanning-tree bpduguard
    • 2.2.6 spanning-tree bpdumigrationcheck
    • 2.2.7 spanning-tree configuration name
      • 2.2.7.1 no spanning-tree configuration name
    • 2.2.8 spanning-tree configuration revision
      • 2.2.8.1 no spanning-tree configuration revision
    • 2.2.9 spanning-tree edgeport
      • 2.2.9.1 no spanning-tree edgeport
    • 2.2.10 spanning-tree forceversion
      • 2.2.10.1 no spanning-tree forceversion
    • 2.2.11 spanning-tree forward-time
      • 2.2.11.1 no spanning-tree forward-time
    • 2.2.12 spanning-tree hello-time
      • 2.2.12.1 no spanning-tree hello-time
    • 2.2.13 spanning-tree max-age
      • 2.2.13.1 no spanning-tree max-age
    • 2.2.14 spanning-tree max-hops
      • 2.2.14.1 no spanning-tree max-hops
    • 2.2.15 spanning-tree mst
      • 2.2.15.1 no spanning-tree mst
    • 2.2.16 spanning-tree mst instance
      • 2.2.16.1 no spanning-tree mst instance
    • 2.2.17 spanning-tree mst priority
      • 2.2.17.1 no spanning-tree mst priority
    • 2.2.18 spanning-tree mst vlan
      • 2.2.18.1 no spanning-tree mst vlan
    • 2.2.19 spanning-tree port mode
      • 2.2.19.1 no spanning-tree port mode
    • 2.2.20 spanning-tree port mode all
      • 2.2.20.1 no spanning-tree port mode all
    • 2.2.21 spanning-tree port-state
    • 2.2.22 spanning-tree rootguard
      • 2.2.22.1 no spanning-tree rootguard
    • 2.2.23 show spanning-tree
    • 2.2.24 show spanning-tree brief
    • 2.2.25 show spanning-tree interface
    • 2.2.26 show spanning-tree mst port detailed
    • 2.2.27 show spanning-tree mst port summary
    • 2.2.28 show spanning-tree mst summary
    • 2.2.29 show spanning-tree summary
    • 2.2.30 show spanning-tree vlan
  • 2.3 VLAN Commands
    • 2.3.1 vlan database
    • 2.3.2 network mgmt_vlan
      • 2.3.2.1 no network mgmt_vlan
    • 2.3.3 vlan
      • 2.3.3.1 no vlan
    • 2.3.4 vlan acceptframe
      • 2.3.4.1 no vlan acceptframe
    • 2.3.5 vlan ingressfilter
      • 2.3.5.1 no vlan ingressfilter
    • 2.3.6 vlan makestatic
    • 2.3.7 vlan name
      • 2.3.7.1 no vlan name
    • 2.3.8 vlan participation
    • 2.3.9 vlan participation all
    • 2.3.10 vlan port acceptframe all
      • 2.3.10.1 no vlan port acceptframe all
    • 2.3.11 vlan port ingressfilter all
      • 2.3.11.1 no vlan port ingressfilter all
    • 2.3.12 vlan port pvid all
      • 2.3.12.1 no vlan port pvid all
    • 2.3.13 vlan port tagging all
      • 2.3.13.1 no vlan port tagging all
    • 2.3.14 vlan protocol group
    • 2.3.15 vlan protocol group add protocol
      • 2.3.15.1 no vlan protocol group add protocol
    • 2.3.16 vlan protocol group remove
    • 2.3.17 protocol group
      • 2.3.17.1 no protocol group
    • 2.3.18 protocol vlan group
      • 2.3.18.1 no protocol vlan group
    • 2.3.19 protocol vlan group all
      • 2.3.19.1 no protocol vlan group all
    • 2.3.20 vlan pvid
      • 2.3.20.1 no vlan pvid
    • 2.3.21 vlan tagging
      • 2.3.21.1 no vlan tagging
    • 2.3.22 vlan association subnet
      • 2.3.22.1 no vlan association subnet
    • 2.3.23 vlan association mac
      • 2.3.23.1 no vlan association mac
    • 2.3.24 show vlan
    • 2.3.25 show vlan brief
    • 2.3.26 show vlan port
    • 2.3.27 show vlan association subnet
    • 2.3.28 show vlan association mac
  • 2.4 Double VLAN Commands
    • 2.4.1 dvlan-tunnel ethertype
    • 2.4.2 mode dot1q-tunnel
      • 2.4.2.1 no mode dot1q-tunnel
    • 2.4.3 mode dvlan-tunnel
      • 2.4.3.1 no mode dvlan-tunnel
    • 2.4.4 show dot1q-tunnel
    • 2.4.5 show dvlan-tunnel
  • 2.5 Voice VLAN Commands
    • 2.5.1 voice vlan (Global Config)
      • 2.5.1.1 no voice vlan (Global Config)
    • 2.5.2 voice vlan (Interface Config)
      • 2.5.2.1 no voice vlan (Interface Config)
    • 2.5.3 voice vlan data priority
    • 2.5.4 show voice vlan
  • 2.6 Provisioning (IEEE 802.1p) Commands
    • 2.6.1 vlan port priority all
    • 2.6.2 vlan priority
  • 2.7 Protected Ports Commands
    • 2.7.1 switchport protected (Global Config)
      • 2.7.1.1 no switchport protected (Global Config)
    • 2.7.2 switchport protected (Interface Config)
      • 2.7.2.1 no switchport protected (Interface Config)
    • 2.7.3 show switchport protected
    • 2.7.4 show interfaces switchport
  • 2.8 GARP Commands
    • 2.8.1 set garp timer join
      • 2.8.1.1 no set garp timer join
    • 2.8.2 set garp timer leave
      • 2.8.2.1 no set garp timer leave
    • 2.8.3 set garp timer leaveall
      • 2.8.3.1 no set garp timer leaveall
    • 2.8.4 show garp
  • 2.9 GVRP Commands
    • 2.9.1 set gvrp adminmode
      • 2.9.1.1 no set gvrp adminmode
    • 2.9.2 set gvrp interfacemode
      • 2.9.2.1 no set gvrp interfacemode
    • 2.9.3 show gvrp configuration
  • 2.10 GMRP Commands
    • 2.10.1 set gmrp adminmode
      • 2.10.1.1 no set gmrp adminmode
    • 2.10.2 set gmrp interfacemode
      • 2.10.2.1 no set gmrp interfacemode
    • 2.10.3 show gmrp configuration
    • 2.10.4 show mac-address-table gmrp
  • 2.11 Port-Based Network Access Control Commands
    • 2.11.1 authentication login
      • 2.11.1.1 no authentication login
    • 2.11.2 clear dot1x statistics
    • 2.11.3 clear radius statistics
    • 2.11.4 dot1x default-login
    • 2.11.5 dot1x guest-vlan
      • 2.11.5.1 no dot1x guest-vlan
    • 2.11.6 dot1x initialize
    • 2.11.7 dot1x login
    • 2.11.8 dot1x max-req
      • 2.11.8.1 no dot1x max-req
    • 2.11.9 dot1x max-users
      • 2.11.9.1 no dot1x max-users
    • 2.11.10 dot1x port-control
      • 2.11.10.1 no dot1x port-control
    • 2.11.11 dot1x port-control all
      • 2.11.11.1 no dot1x port-control all
    • 2.11.12 dot1x re-authenticate
    • 2.11.13 dot1x re-authentication
      • 2.11.13.1 no dot1x re-authentication
    • 2.11.14 dot1x system-auth-control
      • 2.11.14.1 no dot1x system-auth-control
    • 2.11.15 dot1x timeout
      • 2.11.15.1 no dot1x timeout
    • 2.11.16 dot1x unauthenticated-vlan
      • 2.11.16.1 no dot1x unauthenticated-vlan
    • 2.11.17 dot1x user
      • 2.11.17.1 no dot1x user
    • 2.11.18 users defaultlogin
    • 2.11.19 users login
    • 2.11.20 show authentication
    • 2.11.21 show authentication users
    • 2.11.22 show dot1x
    • 2.11.23 show dot1x clients
    • 2.11.24 show dot1x users
    • 2.11.25 show users authentication
  • 2.12 Storm-Control Commands
    • 2.12.1 storm-control broadcast
      • 2.12.1.1 no storm-control broadcast
    • 2.12.2 storm-control broadcast level
      • 2.12.2.1 no storm-control broadcast level
    • 2.12.3 storm-control broadcast rate
      • 2.12.3.1 no storm-control broadcast rate
    • 2.12.4 storm-control broadcast all
      • 2.12.4.1 no storm-control broadcast all
    • 2.12.5 storm-control broadcast all level
      • 2.12.5.1 no storm-control broadcast all level
    • 2.12.6 storm-control broadcast all rate
      • 2.12.6.1 no storm-control broadcast all rate
    • 2.12.7 storm-control multicast
      • 2.12.7.1 no storm-control multicast
    • 2.12.8 storm-control multicast level
      • 2.12.8.1 no storm-control multicast level
    • 2.12.9 storm-control multicast rate
      • 2.12.9.1 no storm-control multicast rate
    • 2.12.10 storm-control multicast all
      • 2.12.10.1 no storm-control multicast all
    • 2.12.11 storm-control multicast all level
      • 2.12.11.1 no storm-control multicast all level
    • 2.12.12 storm-control multicast all rate
      • 2.12.12.1 no storm-control multicast all rate
    • 2.12.13 storm-control unicast
      • 2.12.13.1 no storm-control unicast
    • 2.12.14 storm-control unicast level
      • 2.12.14.1 no storm-control unicast level
    • 2.12.15 storm-control unicast rate
      • 2.12.15.1 no storm-control uniicast rate
    • 2.12.16 storm-control unicast all
      • 2.12.16.1 no storm-control unicast all
    • 2.12.17 storm-control unicast all level
      • 2.12.17.1 no storm-control unicast all level
    • 2.12.18 storm-control unicast all rate
      • 2.12.18.1 no storm-control unicast all rate
    • 2.12.19 storm-control flowcontrol
      • 2.12.19.1 no storm-control flowcontrol
    • 2.12.20 show storm-control
  • 2.13 Port-Channel/LAG (802.3ad) Commands
    • 2.13.1 port-channel
      • 2.13.1.1 no port-channel
    • 2.13.2 addport
    • 2.13.3 deleteport (Interface Config)
    • 2.13.4 deleteport (Global Config)
    • 2.13.5 lacp admin key
      • 2.13.5.1 no lacp admin key
    • 2.13.6 lacp collector max-delay
      • 2.13.6.1 no lacp collector max delay
    • 2.13.7 lacp actor admin
    • 2.13.8 lacp actor admin key
      • 2.13.8.1 no lacp actor admin key
    • 2.13.9 lacp actor admin state
      • 2.13.9.1 no lacp actor admin state
    • 2.13.10 lacp actor admin state individual
      • 2.13.10.1 no lacp actor admin state individual
    • 2.13.11 lacp actor admin state longtimeout
      • 2.13.11.1 no lacp actor admin state longtimeout
    • 2.13.12 lacp actor admin state passive
      • 2.13.12.1 no lacp actor admin state passive
    • 2.13.13 lacp actor port
    • 2.13.14 lacp actor port priority
      • 2.13.14.1 no lacp actor port priority
    • 2.13.15 lacp actor system priority
      • 2.13.15.1 no lacp actor system priority
    • 2.13.16 lacp partner admin key
      • 2.13.16.1 no lacp partner admin key
    • 2.13.17 lacp partner admin state
      • 2.13.17.1 no lacp partner admin state
    • 2.13.18 lacp partner admin state individual
      • 2.13.18.1 no lacp partner admin state individual
    • 2.13.19 lacp partner admin state longtimeout
      • 2.13.19.1 no lacp partner admin state longtimeout
    • 2.13.20 lacp partner admin state passive
      • 2.13.20.1 no lacp partner admin state passive
    • 2.13.21 lacp partner port id
      • 2.13.21.1 no lacp partner port id
    • 2.13.22 lacp partner port priority
      • 2.13.22.1 no lacp partner port priority
    • 2.13.23 lacp partner system-id
      • 2.13.23.1 no lacp partner system-id
    • 2.13.24 lacp partner system priority
      • 2.13.24.1 no lacp partner system priority
    • 2.13.25 port-channel static
      • 2.13.25.1 no port-channel static
    • 2.13.26 port lacpmode
      • 2.13.26.1 no port lacpmode
    • 2.13.27 port lacpmode all
      • 2.13.27.1 no port lacpmode all
    • 2.13.28 port lacptimeout (Interface Config)
      • 2.13.28.1 no port lacptimeout
    • 2.13.29 port lacptimeout (Global Config)
      • 2.13.29.1 no port lacptimeout
    • 2.13.30 port-channel adminmode
      • 2.13.30.1 no port-channel adminmode
    • 2.13.31 port-channel linktrap
      • 2.13.31.1 no port-channel linktrap
    • 2.13.32 port-channel load-balance
      • 2.13.32.1 no port-channel load-balance
    • 2.13.33 port-channel hash multicast
    • 2.13.34 port-channel name
    • 2.13.35 port-channel system priority
      • 2.13.35.1 no port-channel system priority
    • 2.13.36 show lacp actor
    • 2.13.37 show lacp partner
    • 2.13.38 show port-channel brief
    • 2.13.39 show port-channel
    • 2.13.40 show port-channel system priority
    • 2.13.41 show port-channel hash multicast
  • 2.14 Port Mirroring
    • 2.14.1 monitor session
      • 2.14.1.1 no monitor session
    • 2.14.2 no monitor
    • 2.14.3 show monitor session
  • 2.15 Static MAC Filtering
    • 2.15.1 macfilter
      • 2.15.1.1 no macfilter
    • 2.15.2 macfilter adddest
      • 2.15.2.1 no macfilter adddest
    • 2.15.3 macfilter adddest all
      • 2.15.3.1 no macfilter adddest all
    • 2.15.4 macfilter addsrc
      • 2.15.4.1 no macfilter addsrc
    • 2.15.5 macfilter addsrc all
      • 2.15.5.1 no macfilter addsrc all
    • 2.15.6 show mac-address-table static
    • 2.15.7 show mac-address-table staticfiltering
  • 2.16 DHCP Snooping Configuration Commands
    • 2.16.1 ip dhcp snooping
      • 2.16.1.1 no ip dhcp snooping
    • 2.16.2 ip dhcp snooping vlan
      • 2.16.2.1 no ip dhcp snooping vlan
    • 2.16.3 ip dhcp snooping verify mac-address
      • 2.16.3.1 no ip dhcp snooping verify mac-address
    • 2.16.4 ip dhcp snooping database
    • 2.16.5 ip dhcp snooping database write-delay
      • 2.16.5.1 no ip dhcp snooping database write-delay
    • 2.16.6 ip dhcp snooping binding
      • 2.16.6.1 no ip dhcp snooping binding
    • 2.16.7 ip verify binding
      • 2.16.7.1 no ip verify binding
    • 2.16.8 ip dhcp snooping limit
      • 2.16.8.1 no ip dhcp snooping limit
    • 2.16.9 ip dhcp snooping log-invalid
      • 2.16.9.1 no ip dhcp snooping log-invalid
    • 2.16.10 ip dhcp snooping trust
      • 2.16.10.1 no ip dhcp snooping trust
    • 2.16.11 ip verify source
      • 2.16.11.1 no ip verify source
    • 2.16.12 show ip dhcp snooping
    • 2.16.13 show ip dhcp snooping binding
    • 2.16.14 show ip dhcp snooping database
    • 2.16.15 show ip dhcp snooping statistics
    • 2.16.16 clear ip dhcp snooping binding
    • 2.16.17 clear ip dhcp snooping statistics
    • 2.16.18 show ip verify source
    • 2.16.19 show ip source binding
  • 2.17 Dynamic ARP Inspection Commands
    • 2.17.1 ip arp inspection vlan
      • 2.17.1.1 no ip arp inspection vlan
    • 2.17.2 ip arp inspection validate
      • 2.17.2.1 no ip arp inspection validate
    • 2.17.3 ip arp inspection vlan logging
      • 2.17.3.1 no ip arp inspection vlan logging
    • 2.17.4 ip arp inspection trust
      • 2.17.4.1 no ip arp inspection trust
    • 2.17.5 ip arp inspection limit
      • 2.17.5.1 no ip arp inspection limit
    • 2.17.6 ip arp inspection filter
      • 2.17.6.1 no ip arp inspection filter
    • 2.17.7 arp access-list
      • 2.17.7.1 no arp access-list
    • 2.17.8 permit ip host mac host
      • 2.17.8.1 no permit ip host mac host
    • 2.17.9 show ip arp inspection
    • 2.17.10 show ip arp inspection statistics
    • 2.17.11 clear ip arp inspection statistics
    • 2.17.12 show ip arp inspection interfaces
    • 2.17.13 show arp access-list
  • 2.18 IGMP Snooping Configuration Commands
    • 2.18.1 set igmp
      • 2.18.1.1 no set igmp
    • 2.18.2 set igmp interfacemode
      • 2.18.2.1 no set igmp interfacemode
    • 2.18.3 set igmp fast-leave
      • 2.18.3.1 no set igmp fast-leave
    • 2.18.4 set igmp groupmembership-interval
      • 2.18.4.1 no set igmp groupmembership-interval
    • 2.18.5 set igmp maxresponse
      • 2.18.5.1 no set igmp maxresponse
    • 2.18.6 set igmp mcrtrexpiretime
      • 2.18.6.1 no set igmp mcrtrexpiretime
    • 2.18.7 set igmp mrouter
      • 2.18.7.1 no set igmp mrouter
    • 2.18.8 set igmp mrouter interface
      • 2.18.8.1 no set igmp mrouter interface
    • 2.18.9 show igmpsnooping
    • 2.18.10 show igmpsnooping mrouter interface
    • 2.18.11 show igmpsnooping mrouter vlan
    • 2.18.12 show mac-address-table igmpsnooping
  • 2.19 IGMP Snooping Querier Commands
    • 2.19.1 set igmp querier
      • 2.19.1.1 no set igmp querier
    • 2.19.2 set igmp querier query-interval
      • 2.19.2.1 no set igmp querier query-interval
    • 2.19.3 set igmp querier timer expiry
      • 2.19.3.1 no set igmp querier timer expiry
    • 2.19.4 set igmp querier version
      • 2.19.4.1 no set igmp querier version
    • 2.19.5 set igmp querier election participate
      • 2.19.5.1 no set igmp querier election participate
    • 2.19.6 show igmpsnooping querier
  • 2.20 MLD Snooping Commands
    • 2.20.1 set mld
      • 2.20.1.1 no set mld
    • 2.20.2 set mld interfacemode
      • 2.20.2.1 no set mld interfacemode
    • 2.20.3 set mld fast-leave
      • 2.20.3.1 no set mld fast-leave
    • 2.20.4 set mld groupmembership-interval
      • 2.20.4.1 no set groupmembership-interval
    • 2.20.5 set mld maxresponse
      • 2.20.5.1 no set mld maxresponse
    • 2.20.6 set mld mcrtexpiretime
      • 2.20.6.1 no set mld mcrtexpiretime
    • 2.20.7 set mld mrouter
      • 2.20.7.1 no set mld mrouter
    • 2.20.8 set mld mrouter interface
      • 2.20.8.1 no set mld mrouter interface
    • 2.20.9 show mldsnooping
    • 2.20.10 show mldsnooping mrouter interface
    • 2.20.11 show mldsnooping mrouter vlan
    • 2.20.12 show mac-address-table mldsnooping
  • 2.21 MLD Snooping Querier Commands
    • 2.21.1 set mld querier
      • 2.21.1.1 no set mld querier
    • 2.21.2 set mld querier query_interval
      • 2.21.2.1 no set mld querier query_interval
    • 2.21.3 set mld querier timer expiry
      • 2.21.3.1 no set mld querier timer expiry
    • 2.21.4 set mld querier election participate
      • 2.21.4.1 no set mld querier election participate
    • 2.21.5 show mldsnooping querier
  • 2.22 Port Security Commands
    • 2.22.1 port-security
      • 2.22.1.1 no port-security
    • 2.22.2 port-security max-dynamic
      • 2.22.2.1 no port-security max-dynamic
    • 2.22.3 port-security max-static
      • 2.22.3.1 no port-security max-static
    • 2.22.4 port-security mac-address
      • 2.22.4.1 no port-security mac-address
    • 2.22.5 port-security mac-address move
    • 2.22.6 show port-security
    • 2.22.7 show port-security dynamic
    • 2.22.8 show port-security static
    • 2.22.9 show port-security violation
  • 2.23 LLDP (802.1AB) Commands
    • 2.23.1 lldp transmit
      • 2.23.1.1 no lldp transmit
    • 2.23.2 lldp receive
      • 2.23.2.1 no lldp receive
    • 2.23.3 lldp timers
      • 2.23.3.1 no lldp timers
    • 2.23.4 lldp transmit-tlv
      • 2.23.4.1 no lldp transmit-tlv
    • 2.23.5 lldp transmit-mgmt
      • 2.23.5.1 no lldp transmit-mgmt
    • 2.23.6 lldp notification
      • 2.23.6.1 no lldp notification
    • 2.23.7 lldp notification-interval
      • 2.23.7.1 no lldp notification-interval
    • 2.23.8 clear lldp statistics
    • 2.23.9 clear lldp remote-data
    • 2.23.10 show lldp
    • 2.23.11 show lldp interface
    • 2.23.12 show lldp statistics
    • 2.23.13 show lldp remote-device
    • 2.23.14 show lldp remote-device detail
    • 2.23.15 show lldp local-device
    • 2.23.16 show lldp local-device detail
  • 2.24 LLDP-MED Commands
    • 2.24.1 lldp med
      • 2.24.1.1 no lldp med
    • 2.24.2 lldp med confignotification
      • 2.24.2.1 no ldp med confignotification
    • 2.24.3 lldp med transmit-tlv
      • 2.24.3.1 no lldp med transmit-tlv
    • 2.24.4 lldp med all
    • 2.24.5 lldp med confignotification all
    • 2.24.6 lldp med faststartrepeatcount
      • 2.24.6.1 no lldp med faststartrepeatcount
    • 2.24.7 lldp med transmit-tlv all
      • 2.24.7.1 no lldp med transmit-tlv
    • 2.24.8 show lldp med
    • 2.24.9 show lldp med interface
    • 2.24.10 show lldp med local-device detail
    • 2.24.11 show lldp med remote-device
    • 2.24.12 show lldp med remote-device detail
  • 2.25 Denial of Service Commands
    • 2.25.1 dos-control all
      • 2.25.1.1 no dos-control all
    • 2.25.2 dos-control sipdip
      • 2.25.2.1 no dos-control sipdip
    • 2.25.3 dos-control firstfrag
      • 2.25.3.1 no dos-control firstfrag
    • 2.25.4 dos-control tcpfrag
      • 2.25.4.1 no dos-control tcpfrag
    • 2.25.5 dos-control tcpflag
      • 2.25.5.1 no dos-control tcpflag
    • 2.25.6 dos-control l4port
      • 2.25.6.1 no dos-control l4port
    • 2.25.7 dos-control icmp
      • 2.25.7.1 no dos-control icmp
    • 2.25.8 show dos-control
  • 2.26 MAC Database Commands
    • 2.26.1 bridge aging-time
      • 2.26.1.1 no bridge aging-time
    • 2.26.2 show forwardingdb agetime
    • 2.26.3 show mac-address-table multicast
    • 2.26.4 show mac-address-table stats
  • 2.27 ISDP Commands
    • 2.27.1 isdp run
      • 2.27.1.1 no isdp run
    • 2.27.2 isdp holdtime
    • 2.27.3 isdp timer
    • 2.27.4 isdp advertise-v2
      • 2.27.4.1 no isdp advertise-v2
    • 2.27.5 isdp enable
      • 2.27.5.1 no isdp enable
    • 2.27.6 clear isdp counters
    • 2.27.7 clear isdp table
    • 2.27.8 show isdp
    • 2.27.9 show isdp interface
    • 2.27.10 show isdp entry
    • 2.27.11 show isdp neighbors
    • 2.27.12 show isdp traffic
    • 2.27.13 debug isdp packet
      • 2.27.13.1 no debug isdp packet
  • 2.28 Multicast Handling Commands
    • 2.28.1 multicast (interface)
    • 2.28.2 show port multicast
    • 2.28.3 multicast (VLAN)
    • 2.28.4 show vlan multicast
    • 2.28.5 set igmp proxy-report interfacemode
      • 2.28.5.1 no set igmp proxy-report interfacemode
  • 2.29 Port Bridging Commands
    • 2.29.1 L2-port-bridge
      • 2.29.1.1 no L2-port-bridge
• 3. Quality of Service (QoS) Commands
  • 3.1 Class of Service (CoS) Commands
    • 3.1.1 classofservice dot1p-mapping
      • 3.1.1.1 no classofservice dot1p-mapping
    • 3.1.2 classofservice ip-dscp-mapping
      • 3.1.2.1 no classofservice ip-dscp-mapping
    • 3.1.3 classofservice trust
      • 3.1.3.1 no classofservice trust
    • 3.1.4 cos-queue min-bandwidth
      • 3.1.4.1 no cos-queue min-bandwidth
    • 3.1.5 cos-queue strict
      • 3.1.5.1 no cos-queue strict
    • 3.1.6 traffic-shape
      • 3.1.6.1 no traffic-shape
    • 3.1.7 show classofservice dot1p-mapping
    • 3.1.8 show classofservice ip-precedence-mapping
    • 3.1.9 show classofservice ip-dscp-mapping
    • 3.1.10 show classofservice trust
    • 3.1.11 show interfaces cos-queue
    • 3.1.12 show interface cos-counter
    • 3.1.13 show packet-memory
    • 3.1.14 packet-memory (configure)
    • 3.1.15 packet-memory (interface)
    • 3.1.16 show protection-group
    • 3.1.17 protection-group (configure)
      • 3.1.17.1 no protection-group (configure)
    • 3.1.18 protection-group (interface)
      • 3.1.18.1 no protection-group (interface)
  • 3.2 Differentiated Services (DiffServ) Commands
    • 3.2.1 diffserv
      • 3.2.1.1 no diffserv
  • 3.3 DiffServ Class Commands
    • 3.3.1 class-map
      • 3.3.1.1 no class-map
    • 3.3.2 class-map rename
    • 3.3.3 match ethertype
    • 3.3.4 match any
    • 3.3.5 match class-map
      • 3.3.5.1 no match class-map
    • 3.3.6 match cos
    • 3.3.7 match secondary-cos
    • 3.3.8 match destination-address mac
    • 3.3.9 match dstip
    • 3.3.10 match dstip6
    • 3.3.11 match dstl4port
    • 3.3.12 match ip dscp
    • 3.3.13 match ip precedence
    • 3.3.14 match ip tos
    • 3.3.15 match protocol
    • 3.3.16 match source-address mac
    • 3.3.17 match srcip
    • 3.3.18 match srcip6
    • 3.3.19 match srcl4port
    • 3.3.20 match vlan
    • 3.3.21 match secondary-vlan
  • 3.4 DiffServ Policy Commands
    • 3.4.1 assign-queue
    • 3.4.2 drop
    • 3.4.3 mirror
    • 3.4.4 redirect
    • 3.4.5 conform-color
    • 3.4.6 class
      • 3.4.6.1 no class
    • 3.4.7 mark cos
    • 3.4.8 mark ip-precedence
    • 3.4.9 police-simple
    • 3.4.10 policy-map
      • 3.4.10.1 no policy-map
    • 3.4.11 policy-map rename
  • 3.5 DiffServ Service Commands
    • 3.5.1 service-policy
      • 3.5.1.1 no service-policy
  • 3.6 DiffServ Show Commands
    • 3.6.1 show class-map
    • 3.6.2 show diffserv
    • 3.6.3 show policy-map
    • 3.6.4 show diffserv service
    • 3.6.5 show diffserv service brief
    • 3.6.6 show policy-map interface
    • 3.6.7 show service-policy
  • 3.7 MAC Access Control List (ACL) Commands
    • 3.7.1 mac access-list extended
      • 3.7.1.1 no mac access-list extended
    • 3.7.2 mac access-list extended rename
    • 3.7.3 {deny | permit} (MAC ACL)
    • 3.7.4 mac access-group
      • 3.7.4.1 no mac access-group
    • 3.7.5 show mac access-lists
  • 3.8 IP Access Control List (ACL) Commands
    • 3.8.1 access-list
      • 3.8.1.1 no access-list
    • 3.8.2 ip access-list
      • 3.8.2.1 no ip access-list
    • 3.8.3 ip access-list rename
    • 3.8.4 {deny | permit} (IP ACL)
    • 3.8.5 ip access-group
      • 3.8.5.1 no ip access-group
    • 3.8.6 acl-trapflags
      • 3.8.6.1 no acl-trapflags
    • 3.8.7 show acl-traptimer
    • 3.8.8 acl-traptimer
      • 3.8.8.1 no acl-traptimer
    • 3.8.9 show ip access-lists
    • 3.8.10 show access-lists
  • 3.9 IPv6 Access Control List (ACL) Commands
    • 3.9.1 ipv6 access-list
      • 3.9.1.1 no ipv6 access-list
    • 3.9.2 ipv6 access-list rename
    • 3.9.3 {deny | permit} (IPv6)
    • 3.9.4 ipv6 traffic-filter
      • 3.9.4.1 no ipv6 traffic-filter
    • 3.9.5 show ipv6 access-lists
  • 3.10 Auto-Voice over IP Commands
    • 3.10.1 auto-voip all
      • 3.10.1.1 no auto-voip all
    • 3.10.2 auto-voip
      • 3.10.2.1 no auto-voip
    • 3.10.3 show auto-voip
• 4. Utility Commands
  • 4.1 Commands for update and startup Configuration
    • 4.1.1 download ipmifw
    • 4.1.2 download amcipmifw
  • 4.2 Dual Image Commands
    • 4.2.1 delete
    • 4.2.2 boot system
    • 4.2.3 show bootvar
    • 4.2.4 filedescr
  • 4.3 ATCA commands
    • 4.3.1 set board sensor threshold
    • 4.3.2 set board device-id
    • 4.3.3 show atca ekeying
    • 4.3.4 ekeying (interface)
      • 4.3.4.1 no ekeying (interface)
    • 4.3.5 ekeying all (configure)
      • 4.3.5.1 no ekeying all (configure)
  • 4.4 System Information and Statistics Commands
    • 4.4.1 show arp switch
    • 4.4.2 show eventlog
    • 4.4.3 show hardware
    • 4.4.4 show version
    • 4.4.5 show interface
    • 4.4.6 show interface ethernet
    • 4.4.7 show mac-addr-table
    • 4.4.8 show process cpu
    • 4.4.9 show running-config
    • 4.4.10 show sysinfo
    • 4.4.11 show tech-support
    • 4.4.12 terminal length
      • 4.4.12.1 no terminal length
    • 4.4.13 show terminal length
    • 4.4.14 show boardinfo post-status
    • 4.4.15 show boardinfo sensors
    • 4.4.16 show boardinfo event-log
    • 4.4.17 show boardinfo update-status
    • 4.4.18 show boardinfo version
    • 4.4.19 show boardinfo address
    • 4.4.20 show boardinfo fru
    • 4.4.21 show boardinfo ipmidev
    • 4.4.22 show boardinfo amc connection
    • 4.4.23 show boardinfo amc fru
    • 4.4.24 show boardinfo amc ipmidev
    • 4.4.25 show boardinfo led
    • 4.4.26 show boardinfo cpu-load
    • 4.4.27 show boardinfo memory-usage
  • 4.5 Logging Commands
    • 4.5.1 logging buffered
      • 4.5.1.1 no logging buffered
    • 4.5.2 logging buffered wrap
      • 4.5.2.1 no logging buffered wrap
    • 4.5.3 logging cli-command
      • 4.5.3.1 no logging cli-command
    • 4.5.4 logging console
      • 4.5.4.1 no logging console
    • 4.5.5 logging host
    • 4.5.6 logging host remove
    • 4.5.7 logging port
      • 4.5.7.1 no logging port
    • 4.5.8 logging syslog
      • 4.5.8.1 no logging syslog
    • 4.5.9 show logging
    • 4.5.10 show logging buffered
    • 4.5.11 show logging hosts
    • 4.5.12 show logging traplogs
    • 4.5.13 clear board event-log
    • 4.5.14 show logging backtrace
    • 4.5.15 show logging errcounter
    • 4.5.16 clear errcounter
    • 4.5.17 show logging persistent
  • 4.6 System Utility and Clear Commands
    • 4.6.1 traceroute
    • 4.6.2 clear config
    • 4.6.3 clear counters
    • 4.6.4 clear igmpsnooping
    • 4.6.5 clear pass
    • 4.6.6 clear port-channel
    • 4.6.7 clear traplog
    • 4.6.8 clear vlan
    • 4.6.9 enable passwd
    • 4.6.10 enable passwd encrypted <password>
    • 4.6.11 logout
    • 4.6.12 ping
    • 4.6.13 quit
    • 4.6.14 reload
    • 4.6.15 reload fast
    • 4.6.16 copy
    • 4.6.17 delete nvram:extra-profile
    • 4.6.18 set bootstopkey
      • 4.6.18.1 no set bootstopkey
  • 4.7 Simple Network Time Protocol (SNTP) Commands
    • 4.7.1 sntp broadcast client poll-interval
      • 4.7.1.1 no sntp broadcast client poll-interval
    • 4.7.2 sntp client mode
      • 4.7.2.1 no sntp client mode
    • 4.7.3 sntp client port
      • 4.7.3.1 no sntp client port
    • 4.7.4 sntp unicast client poll-interval
      • 4.7.4.1 no sntp unicast client poll-interval
    • 4.7.5 sntp unicast client poll-timeout
      • 4.7.5.1 no sntp unicast client poll-timeout
    • 4.7.6 sntp unicast client poll-retry
      • 4.7.6.1 no sntp unicast client poll-retry
    • 4.7.7 sntp server
      • 4.7.7.1 no sntp server
    • 4.7.8 show sntp
    • 4.7.9 show sntp client
    • 4.7.10 show sntp server
  • 4.8 DHCP Server Commands
    • 4.8.1 ip dhcp pool
      • 4.8.1.1 no ip dhcp pool
    • 4.8.2 client-identifier
      • 4.8.2.1 no client-identifier
    • 4.8.3 client-name
      • 4.8.3.1 no client-name
    • 4.8.4 default-router
      • 4.8.4.1 no default-router
    • 4.8.5 dns-server
      • 4.8.5.1 no dns-server
    • 4.8.6 hardware-address
      • 4.8.6.1 no hardware-address
    • 4.8.7 host
      • 4.8.7.1 no host
    • 4.8.8 lease
      • 4.8.8.1 no lease
    • 4.8.9 network (DHCP Pool Config)
      • 4.8.9.1 no network
    • 4.8.10 bootfile
      • 4.8.10.1 no bootfile
    • 4.8.11 domain-name
      • 4.8.11.1 no domain-name
    • 4.8.12 netbios-name-server
      • 4.8.12.1 no netbios-name-server
    • 4.8.13 netbios-node-type
      • 4.8.13.1 no netbios-node-type
    • 4.8.14 next-server
      • 4.8.14.1 no next-server
    • 4.8.15 option
      • 4.8.15.1 no option
    • 4.8.16 ip dhcp excluded-address
      • 4.8.16.1 no ip dhcp excluded-address
    • 4.8.17 ip dhcp ping packets
      • 4.8.17.1 no ip dhcp ping packets
    • 4.8.18 service dhcp
      • 4.8.18.1 no service dhcp
    • 4.8.19 ip dhcp bootp automatic
      • 4.8.19.1 no ip dhcp bootp automatic
    • 4.8.20 ip dhcp conflict logging
      • 4.8.20.1 no ip dhcp conflict logging
    • 4.8.21 clear ip dhcp binding
    • 4.8.22 clear ip dhcp server statistics
    • 4.8.23 clear ip dhcp conflict
    • 4.8.24 show ip dhcp binding
    • 4.8.25 show ip dhcp global configuration
    • 4.8.26 show ip dhcp pool configuration
    • 4.8.27 show ip dhcp server statistics
    • 4.8.28 show ip dhcp conflict
  • 4.9 DHCP Filtering
    • 4.9.1 ip dhcp filtering
      • 4.9.1.1 no ip dhcp filtering
    • 4.9.2 ip dhcp filtering trust
      • 4.9.2.1 no ip dhcp filtering trust
    • 4.9.3 show ip dhcp filtering
  • 4.10 DNS Client Commands
    • 4.10.1 ip domain lookup
      • 4.10.1.1 no ip domain lookup
    • 4.10.2 ip domain name
      • 4.10.2.1 no ip domain name
    • 4.10.3 ip domain list
      • 4.10.3.1 no ip domain list
    • 4.10.4 ip name server
      • 4.10.4.1 no ip name server
    • 4.10.5 ip host
      • 4.10.5.1 no ip host
    • 4.10.6 ip domain retry
      • 4.10.6.1 no ip domain retry
    • 4.10.7 ip domain timeout
      • 4.10.7.1 no ip domain timeout
    • 4.10.8 clear host
    • 4.10.9 show hosts
  • 4.11 Serviceability Packet Tracing Commands
    • 4.11.1 debug arp
      • 4.11.1.1 no debug arp
    • 4.11.2 debug auto-voip
      • 4.11.2.1 no debug auto-voip
    • 4.11.3 debug clear
    • 4.11.4 debug console
      • 4.11.4.1 no debug console
    • 4.11.5 debug dot1x packet
      • 4.11.5.1 no debug dot1x packet
    • 4.11.6 debug igmpsnooping packet
      • 4.11.6.1 no debug igmpsnooping packet
    • 4.11.7 debug igmpsnooping packet transmit
      • 4.11.7.1 no debug igmpsnooping transmit
    • 4.11.8 debug igmpsnooping packet receive
      • 4.11.8.1 no debug igmpsnooping receive
    • 4.11.9 debug ip acl
      • 4.11.9.1 no debug ip acl
    • 4.11.10 debug ip igmp packet
      • 4.11.10.1 no debug ip igmp packet
    • 4.11.11 debug ip mcache packet
      • 4.11.11.1 no debug ip mcache packet
    • 4.11.12 debug lacp packet
      • 4.11.12.1 no debug lacp packet
    • 4.11.13 debug mldsnooping packet
      • 4.11.13.1 no debug mldsnooping packet
    • 4.11.14 debug ping packet
      • 4.11.14.1 no debug ping packet
    • 4.11.15 debug sflow packet
      • 4.11.15.1 no debug sflow packet
    • 4.11.16 debug spanning-tree bpdu
      • 4.11.16.1 no debug spanning-tree bpdu
    • 4.11.17 debug spanning-tree bpdu receive
      • 4.11.17.1 no debug spanning-tree bpdu receive
    • 4.11.18 debug spanning-tree bpdu transmit
      • 4.11.18.1 no debug spanning-tree bpdu transmit
    • 4.11.19 logging persistent
      • 4.11.19.1 no logging persistent
  • 4.12 Cable Test Command
    • 4.12.1 cablestatus
  • 4.13 sFlow Commands
    • 4.13.1 sflow receiver
      • 4.13.1.1 no sflow receiver
    • 4.13.2 sflow sampler
      • 4.13.2.1 no sflow sampler
    • 4.13.3 sflow poller
      • 4.13.3.1 no sflow poller
    • 4.13.4 show sflow agent
    • 4.13.5 show sflow receivers
    • 4.13.6 show sflow samplers
• 5. Management Commands
  • 5.1 Network Interface Commands
    • 5.1.1 enable (Privileged EXEC access)
    • 5.1.2 serviceport ip
    • 5.1.3 serviceport protocol
    • 5.1.4 network parms
    • 5.1.5 network protocol
    • 5.1.6 network mac-address
    • 5.1.7 network mac-type
      • 5.1.7.1 no network mac-type
    • 5.1.8 show network
    • 5.1.9 show serviceport
  • 5.2 Console Port Access Commands
    • 5.2.1 configuration
    • 5.2.2 lineconfig
    • 5.2.3 serial baudrate
      • 5.2.3.1 no serial baudrate
    • 5.2.4 serial timeout
      • 5.2.4.1 no serial timeout
    • 5.2.5 show serial
  • 5.3 Telnet Commands
    • 5.3.1 ip telnet server enable
      • 5.3.1.1 no ip telnet server enable
    • 5.3.2 telnet
    • 5.3.3 transport input telnet
      • 5.3.3.1 no transport input telnet
    • 5.3.4 transport output telnet
      • 5.3.4.1 no transport output telnet
    • 5.3.5 session-limit
      • 5.3.5.1 no session-limit
    • 5.3.6 session-timeout
      • 5.3.6.1 no session-timeout
    • 5.3.7 telnetcon maxsessions
      • 5.3.7.1 no telnetcon maxsessions
    • 5.3.8 telnetcon timeout
      • 5.3.8.1 no telnetcon timeout
    • 5.3.9 show telnet
    • 5.3.10 show telnetcon
  • 5.4 Secure Shell (SSH) Commands
    • 5.4.1 ip ssh
    • 5.4.2 ip ssh protocol
    • 5.4.3 ip ssh server enable
      • 5.4.3.1 no ip ssh server enable
    • 5.4.4 sshcon maxsessions
      • 5.4.4.1 no sshcon maxsessions
    • 5.4.5 sshcon timeout
      • 5.4.5.1 no sshcon timeout
    • 5.4.6 show ip ssh
  • 5.5 Management Security Commands
    • 5.5.1 crypto certificate generate
      • 5.5.1.1 no crypto certificate generate
    • 5.5.2 crypto key generate rsa
      • 5.5.2.1 no crypto key generate rsa
    • 5.5.3 crypto key generate dsa
      • 5.5.3.1 no crypto key generate dsa
  • 5.6 Access Commands
    • 5.6.1 disconnect
    • 5.6.2 show loginsession
  • 5.7 User Account Commands
    • 5.7.1 users name
      • 5.7.1.1 no users name
    • 5.7.2 users name <username> unlock
    • 5.7.3 users passwd
      • 5.7.3.1 no users passwd
    • 5.7.4 users passwd <username> encrypted <password>
    • 5.7.5 users snmpv3 accessmode
      • 5.7.5.1 no users snmpv3 accessmode
    • 5.7.6 users snmpv3 authentication
      • 5.7.6.1 no users snmpv3 authentication
    • 5.7.7 users snmpv3 encryption
      • 5.7.7.1 no users snmpv3 encryption
    • 5.7.8 show users
    • 5.7.9 show users accounts
    • 5.7.10 passwd
    • 5.7.11 passwords min-length
      • 5.7.11.1 no passwords min-length
    • 5.7.12 passwords history
      • 5.7.12.1 no passwords history
    • 5.7.13 passwords aging
      • 5.7.13.1 no passwords aging
    • 5.7.14 passwords lock-out
      • 5.7.14.1 no passwords lock-out
    • 5.7.15 show passwords configuration
    • 5.7.16 write memory
  • 5.8 SNMP Commands
    • 5.8.1 snmp-server
    • 5.8.2 snmp-server community
      • 5.8.2.1 no snmp-server community
    • 5.8.3 snmp-server community ipaddr
      • 5.8.3.1 no snmp-server community ipaddr
    • 5.8.4 snmp-server community ipmask
      • 5.8.4.1 no snmp-server community ipmask
    • 5.8.5 snmp-server community mode
      • 5.8.5.1 no snmp-server community mode
    • 5.8.6 snmp-server community ro
    • 5.8.7 snmp-server enable traps violation
      • 5.8.7.1 no snmp-server enable traps violation
    • 5.8.8 snmp-server enable traps
      • 5.8.8.1 no snmp-server enable traps
    • 5.8.9 snmp-server enable traps linkmode
      • 5.8.9.1 no snmp-server enable traps linkmode
    • 5.8.10 snmp-server enable traps multiusers
      • 5.8.10.1 no snmp-server enable traps multiusers
    • 5.8.11 snmp-server enable traps pll
      • 5.8.11.1 no snmp-server enable traps pll
    • 5.8.12 snmp-server enable traps stpmode
      • 5.8.12.1 no snmp-server enable traps stpmode
    • 5.8.13 snmptrap
      • 5.8.13.1 no snmptrap
    • 5.8.14 snmptrap snmpversion
    • 5.8.15 snmptrap ipaddr
    • 5.8.16 snmptrap mode
      • 5.8.16.1 no snmptrap mode
    • 5.8.17 snmp trap link-status
      • 5.8.17.1 no snmp trap link-status
    • 5.8.18 snmp trap link-status all
      • 5.8.18.1 no snmp trap link-status all
    • 5.8.19 show snmpcommunity
    • 5.8.20 show snmptrap
    • 5.8.21 show trapflags
    • 5.8.22 snmptrap notification
    • 5.8.23 snmp-server engine-id
    • 5.8.24 show snmp-engine-id
    • 5.8.25 set board snmp site
      • 5.8.25.1 no set board snmp site
    • 5.8.26 show boardinfo snmp site
    • 5.8.27 set board snmp ipmi-trap
    • 5.8.28 set board snmp ipmi-trap interval
    • 5.8.29 set board snmp ipmi-trap filter
      • 5.8.29.1 no set board snmp ipmi-trap filter
    • 5.8.30 enable (filter)
    • 5.8.31 disable (filter)
    • 5.8.32 ipmb (filter)
    • 5.8.33 type (filter)
    • 5.8.34 status (filter)
    • 5.8.35 assert (filter)
    • 5.8.36 show boardinfo snmp ipmi-trap
  • 5.9 RADIUS Commands
    • 5.9.1 authorization network radius
      • 5.9.1.1 no authorization network radius
    • 5.9.2 radius accounting mode
      • 5.9.2.1 no radius accounting mode
    • 5.9.3 radius server attribute
      • 5.9.3.1 no radius server attribute
    • 5.9.4 radius server host
      • 5.9.4.1 no radius server host
    • 5.9.5 radius server key
    • 5.9.6 radius server msgauth
      • 5.9.6.1 no radius server msgauth
    • 5.9.7 radius server primary
    • 5.9.8 radius server retransmit
      • 5.9.8.1 no radius server retransmit
    • 5.9.9 radius server timeout
      • 5.9.9.1 no radius server timeout
    • 5.9.10 show radius
    • 5.9.11 show radius servers
    • 5.9.12 show radius accounting
    • 5.9.13 show radius accounting statistics
    • 5.9.14 show radius statistics
  • 5.10 TACACS+ Commands
    • 5.10.1 tacacs-server host
      • 5.10.1.1 no tacacs-server host
    • 5.10.2 tacacs-server key
      • 5.10.2.1 no tacacs-server key
    • 5.10.3 tacacs-server timeout
      • 5.10.3.1 no tacacs-server timeout
    • 5.10.4 key
    • 5.10.5 port
    • 5.10.6 priority
    • 5.10.7 timeout
    • 5.10.8 show tacacs
  • 5.11 Configuration Scripting Commands
    • 5.11.1 script apply
    • 5.11.2 script delete
    • 5.11.3 script list
    • 5.11.4 script show
    • 5.11.5 script validate
  • 5.12 Pre-login Banner and System Prompt Commands
    • 5.12.1 copy (pre-login banner)
    • 5.12.2 set prompt
  • 5.13 Diagnostics Commands
    • 5.13.1 diagnostics
    • 5.13.2 show logging diag-report
  • 5.14 PCI express Commands
    • 5.14.1 show boardinfo pcie
  • 5.15 Storage Commands
    • 5.15.1 set board storage connect
    • 5.15.2 show boardinfo storage
  • 5.16 Clock support commands
    • 5.16.1 set board pcie clock
    • 5.16.2 set board pll
    • 5.16.3 show boardinfo pll status
    • 5.16.4 show boardinfo pll config
    • 5.16.5 set board clock bpl
    • 5.16.6 set board clock mux-amc
    • 5.16.7 set board clock mux-bpl
    • 5.16.8 set board clock override
    • 5.16.9 set board clock receiver
    • 5.16.10 set board clock source
    • 5.16.11 show boardinfo clock bpl
    • 5.16.12 show boardinfo clock amc
• A. Getting Help
• B. FASTPATH Log Messages
  • B.1 Core
  • B.2 Utilities
  • B.3 Management
  • B.4 Switching
  • B.5 QoS
  • B.6 Technologies
  • B.7 O/S Support
• C. List of Commands