Freerider FR510DXs2b(Kensington-S) - Manual (Page 32)

32
2. Check the freewheel lever is fully engaged (see page
12 ). If it is engaged you should not be able to push
your machine. If disengaged, 9 bars will flash on your
battery condition mater with the speed lever pressed.
1. Turn off the power 'on' key switch.
2. Inform your authorised
dealer.
If your Freerider does not slow down or behaves erratically:
Freerider
If you find for any reason your Scooter
does not reduce speed when you let go of the forward-
reverse speed lever . Switch your Scooter 'off' with the
on/off key. The parking brake will activate immediately and
stop your Scooter. Beware the scooter will stop very
suddenly, brace yourself with the handlebars, sit back in
your seat.
This operation should only be carried out in an
emergency; continual use of this facility will damage the drive
transmission and motor brake.
The speed controller system incorporates a sophisticated
micro-processor design (Fig 42). It is located under the rear
Warning:
Warning:
Inform your authorised Freerider dealer before using your
machine again.
Warning:
Freerider
If you feel for any reason that your Scooter is not
driving correctly or making an unusual noise, stop using the
machine. Be safe, contact your
dealer, he will be
able to advise you.
IMPORTANT SPEED CONTROLLER
INFORMATION
If your Freerider does not slow down or behaves erratically:
Freerider
Warning:
Warning:
Inform your authorised Freerider dealer before using your
machine again.
Warning:
Freerider
IMPORTANT SPEED CONTROLLER
INFORMATION
Body cover of your Scooter ( see fig 41). The in-built
micro-controller continually monitors the
Scooter's systems to ensure safe and reliable operation.
Speed control system integrity
Internal voltages and circuits
Motor voltages and circuits
Freewheel speed limiting downhill.
Battery voltage
When the battery voltage is low, the 'battery gauge status'
indicator bar light, situated on the control console ( fig 11,
page 9 ) will flash one red bar slowly as a warning to recharge
your batteries. If the 'speed controller' detects a fault the
battery gauge/status indicator will display a number of bar
flashes indicating the nature of the fault.
For example, the controller will not operate if the speed lever
is not in the neutral position ( fig 12, page 11) when the
Scooter is switched 'on'. Return the speed lever to the neutral
position, when the Scooter will be allowed to operate normally
once again. This safety detection is indicated by a steady
rippling display on the battery gauge ( see also Fault Diagnosis
below ).
If your Scooter is turned 'on' but not operated for a set period
of time ( 15 minutes approx )the speed controller system will
automatically turn itself 'off' to conserve valuable battery
energy, you will note the battery gauge is switched off. It can
be turned on again by turning the on/off switch to 'off' and
then to 'on' again.
A reversing buzzer is provided for when you are driving in a
reverse direction. This is an important safety feature to make
other people aware of your change of direction.
Freerider
SAFETY CONDITIONS MONITORED INCLUDE
Freerider
SAFETY CONDITIONS MONITORED INCLUDE
FLASH CODE
(No. Of flashes) FLASH CODE
(No. Of flashes)
Battery needs recharging
Motor disconnected
Motor wiring fault
Not used
Not used
Inhibit active
Speed pot error
Possible controller fault
Motor solenoid brake fault
High battery voltage
STATUS FAULT CODES -The number of bar segments flashing on the battery gauge display indicates the type of fault STATUS FAULT CODES
1 Flash
2 Flashes
3 Flashes
4 Flashes
5 Flashes
6 Flashes
7 Flashes
8 Flashes
9 Flashes
10 Flashes
The battery voltage has dropped below 16volits in
neutral. Recharge the batteries. Check the battery
condition and the connections.
Motor plug disconnected. Check motor, motor
connectors and wiring.
Motor short or wiring fault. Check motor plug check
motor brushes change motor. If above checks fail to
correct fault, change controller.
Battery charger connected.
Driving inhibited
Drive inhibited
Drive inhibited
Drive inhibited
Drive inhibited
Drive inhibited
Drive inhibited
Drive inhibited
FAULT DISPLAYED
BY PROGRAMMER FAULT DISPLAYED
BY PROGRAMMER FREERIDER SCOOTER
CONDITION FREERIDER SCOOTER
CONDITION COMMENT
Check speed pot wiring for open or short circuits.
Speed pot may not be correctly set up . Contact your
Service Agent.
Fault detected in main controller-contact Service Agent..
Fault detected in solenoid brake or connection to it or
freewheel lever activated.
Battery voltage at the controller is greater than 38
volts. Check condition of batteries and connections.
Supect a charger malfunction.
(speed control lever)