Specifications, Mounting the sensor head – KEYENCE CZ-V22A(P) User Manual

Page 9

Advertising
background image

9

E CZ-V21A(P)/V22A(P)-IM

SPECIFICATIONS

■ Sensor head

*1 Reference distance

Small: 65 mm, medium: 60 mm, large: 50 mm

*2 Large spot: 15 ± 5 mm, small spot: 15 ± 3 mm
*3 The focus distance is about 10 mm, but stable detection can be achieved

with 15 mm.

■ Amplifier unit

*1 20 mA maximum when several units are connected.
*2 When several units are connected, the acceptable ambient temperature var-

ies depending on the conditions given below. To connect several units, be
sure to mount them to a DIN rail. Ensure that the output current is 20 mA max.
When 1 to 2 units are connected: -10 to +50 °C
When 3 units are connected: -10 to +45 °C

MOUNTING THE SENSOR HEAD

■ Extraneous light

A detection error may occur when the light from high-frequency lighting equipment
such as an inverter fluorescent lamp directly enters or reflected on the target into
the emitter. In such a case, apply a light shield plate or change the location of the
sensor.

■ Target movement and sensor orientation

To stabilize the sensor output at a border, mount the sensor as shown in the
following figure as much as possible.

■ When using the CZ-H32

When detecting a metal surface or glossy target

When a target has a metal or glossy surface, the calibration/differentiation
may fail. To detect such a target, tilt the sensor head by approximately 10 to
15 degrees.

■ When using the CZ-H35S/CZ-H37S/H72

When a target has a glossy surface (a birefringence target such as an ori-
ented film), the detection may fail depending on the mounting orientation. To
detect such a target, displace the sensor head by approximately 45 degrees.

Type

Spot

selectable

Canceling glaze

Fluorescent

object

detection

Luster

detection

Model

CZ-H32

CZ-

H35S

CZ-H37S

(small

spot)

CZ-H52

CZ-H72

Detecting range

(mm)

50 to 95

28 to 52

11 to 20

25 to 55

15-mm

center

*2

Recommended

setting distance

(mm)

70

40

15

35

15

Minimum spot

diameter

Depending on

the reference

distance*

Small: ø3/

medium: ø4.5/

large: ø5.5

Setting

distance

40 mm

ø4.5

Setting

distance

16 mm

ø1

At the

setting

distance of

25 mm:

ø10

At the

setting

distance

of

15 mm

*3

:

Small:

approx. ø3

large:

approx. ø5

Light source

Red LED (665nm)

Green LED (520nm)

Bule LED (465nm)

UV

(ultraviolet)

LED

(35 nm)

Red LED

(665nm)

Received light

wavelength

(at receiver)

–

425 to 550

nm

–

Tolerated

bending radius of

fiber (mm)

R25

R15

–

R25

Operating

ambient

temperature:

–10 to +55°C (No freezing)

Operating

ambient

illumination

Incandescent lamp: 10000 rx or less

Sunlight: 20000 rx or less

Protection

structure

IP40

Materi

als

Housing

Glass reinforced resin

Lens

cover

Polyarylate

Triacetate

Polyarylate

(Metal part: SUS304)

Glass

Weight

(including 2-m

cable)

Approx. 40 g

Approx.

45 g

Approx. 40 g

Approx.

50 g

Model

NPN output

CZ-V21A

CZ-V22A

PNP output

CZ-V21AP

CZ-V22AP

Main/sub

Main unit

Sub-unit

Response speed

200

µ s (HIGH SPEED)/1 ms (FINE)/4 ms (TURBO) /

8 ms (SUPER)

Control output*

1

NPN (PNP) open collector x 4 CHs 40 VDC (30 VDC) max.
100 mA max. per output, 200 mA max. for the total of four
outputs
Residual voltage 1 V max.

External calibration input

No voltage input
Input response time 20 ms min.

External bank selection
input (C/C+I mode)

External shift input
(Super I mode)

Protection circuit

Reverse-polarity protection, overcurrent protection, surge
absorber

Power supply voltage

24 VDC, Ripple (P-P): 10% max, Class 2
(the power-on reset time is 3 seconds.)

Current consumption

Normal mode: 1.5 W (62.5 mA max.)
Eco mode: 1 W (42 mA max.)

IEC Class (IEC 60825-1)

Class 1 LED product

Operating ambient
temperature*

2

–10 to +55°C (No freezing)

Vibration

10 to 55 Hz, 1.5 mm double amplitude in the X, Y, and Z
directions, 2 hours respectively

Materials

Housing material: Plycarbonate

Weight (including 2-m cable)

Approx. 110 g

Approx. 100 g

Inverter fluorescent lamp, etc.

Light shield plate

Movement direction

Movement direction

10° to 15°

45°

Advertising
This manual is related to the following products: