Toa VM-3000 Series - Manual (Page 138)

138
230 V AC, 50/60 Hz
600 W (at rated output), 260 W (according to EN60065)
240 W
50 Hz – 20 kHz, ±3 dB (at 1/3 rated output)
0.7% or less (at rated output, 1 kHz)
85 dB or more
Sampling frequency: 48 kHz
A/D D/A converter:
24 bit
Input 1 – 3: –50 dB* (MIC) / –10 dB* (LINE) (changeable), 600 Ω,
electronically balanced,
combined XLR connector (female) / phone jack
Input 4: –50 dB* (MIC) / –10 dB* (LINE) (changeable), 600 Ω,
electronically balanced, removable terminal block (14 pins)
BGM 1 – 2: –10 dB*, 10 kΩ, unbalanced, RCA pin jack
External AMP Input: 100 V line, removable terminal block (14 pins)
Speaker output 1 – 2: Max. (240 W) per output
Speaker output 3 – 6: Max. (120 W) per output
Speaker output 1 – 6: Total within 240 W, removable terminal block (14 pins)
Allowable minimum load:
500 Ω (20 W) at 100 V line for speaker line failure
detection
Direct output: Direct output from internal or external amplifier,
removable terminal block (16 pins)
Recording output BGM/Paging: 0 dB*, 10 kΩ, unbalanced, RCA pin jack
Input 1 – 2: Connecting the RM-300MF/200M Remote Microphone,
RJ45 female connector
Maximum distance: Total 800 m between this unit and remote microphones
Link cable:
Category 5 Shielded Twisted-Pair straight cable (CAT5-STP)
10BASE-T/100BASE-TX (selectable by automatic negotiation), RJ45 female connector
Maximum distance: 100 m between this unit and a switching hub
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP)
Output: Connecting the VM-3240E or VM-3360E, RJ45 female connector
Maximum distance: Total 800 m
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP)
Connecting the VP-2241 or VP-2421, RJ45 female connector
Maximum distance: 5 m
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP)
Input 1 – 8: No-Voltage make contact input, open voltage: 24 V DC,
short-circuit current: 2 mA or less, removable terminal block (14 pins)
Output 1 – 8: Isolated open collector output, withstand voltage: 30 V DC,
operating current: 10 mA or less, removable terminal block (14 pins)
Input 1 – 5: No-Voltage make contact input, open voltage: 24 V DC,
short-circuit current: 2 mA or less, RJ45 female connector
Input 6: Isolated voltage input, Inactive: –24 V ±20%, Active: +24 V ±20%,
RJ45 female connector
Status out: Relay contact output, withstand voltage: 40 V DC,
operating current: 2 – 300 mA, RJ45 female connector
Relay contact 1 – 6, 125 V AC or 30 V DC, total under 5 A,
removable terminal block (16 pins)
Power in: Connecting the VX-2000DS only (operating range: 20 – 40 V DC)
PS out:
28 V DC / 18 A
M4 screw terminal, distance between barriers: 11 mm
24 V DC, Maximum feeding current 0.3 A
16. SPECIFICATIONS
16.1. VM-3240VA Voice Alarm System Amplifier
Power Source
Power Consumption
Rated Output
Frequency Response
Distortion
S/N Ratio
Audio Input/Output
Characteristic
Input
Output
RM Link
Network I/F
VM Link
EXT PA Link
General Control
Emergency Control
ATT Control
Power Input/Output
24 V DC Output