Twin needle sewing, Costura con aguja doble – SINGER 7021 Merritt User Manual

Page 70

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

8. TWIN NEEDLE

SEWING

Twin needle sewing produces two parallel

lines of closely-spaced decorative stitching.

You can sew with either one or two thread

colours.

Your machine is not supplied with the twin

needle or spool pin. These may be obtained

from your local SINGER stockist as optional
accessories.

Recommended settings
Stitch Selection:

Desired stitch

Stitch Width:

j

Stitch Length:

2-5

Foot:

General Purpose (B)

Needle Plate:

General Purpose (A)

• Turn the machine off.

• insert the twin needle with the flat side of

the shank toward the rear of the machine.

• Thread the machine as you normally would

for single needle stitching, except pass the

thread between the centre and the back
tension discs A, and through the left eye

of the twin needle.

• Insert a second spool pin Into the hole on

the top cover of the machine, as Illustrated.

• Thread the machine in the usual way,

except pass the thread from the second

spool between the centre and the front

tension discs B, as shown.

• Pass the thread through the remaining

points, making certain to omit the thread

guide just above the needle and pass

thread through right eye of needle.

• Draw both threads under the foot and back

along with the bobbin thread.

• Slowly lower the needle into the hole in

the needle plate by turning the hand wheel
toward you to make sure the needle clears
the plate.

• Make sure not to use a stitch width greater

than that what is recommended when twin

needle stitching.

8. COSTURA CON

AGUJA DOBLE

La costura con aguja doble produce dos
líneas paralelas de puntos decorativos

debidamente espaciadas.
Su máquina no ha sido complementada ni

con una aguja doble ni con el portacarrete

adicional. No obstante si desea utilizar esta
ventaja, puede adquirir estos accesorios en

su Centro Singer de Costura.

Posiciones recomendadas
Selección punto: el deseado

Anchura punto:

5

—www\/\i\^^^

Longitud punto:

2-5

Prénsatelas:

Uso general (B)

Plancha aguja:

Uso general (A)

• Desconecte la máquina.

• Inserte la aguja doble con el lado plano

del tronco hacia atrás.

• Enhebre la máquina como lo haría nor­

malmente para coser con una aguja, pero
pasando el hilo por el centro y parte
posterior de los discos de tensión Aya

través del ojo Izquierdo de la aguja doble.

• Coloque el segundo portacarrete en su

agujero situado en la cubierta superior,

como se ilustra.

• Enhebre la máquina en la forma usual, pero

pasando el hilo del segundo carrete entre

el centro y la parte anterior de los discos
de tensión B como se muestra.

• Pase el hilo a través de los puntos

restantes, cuidando de no hacerlo por el

guía hilo existente sobre la aguja y a través
del ojo derecho de la aguja.

• Tire de ambos hilos hacia atrás, por debajo

del prénsatelas, junto con el hilo de la

bobina.

• Baje despacio la aguja hacia dentro del

agujero de la plancha de aguja, girando
el volante hacia Vd., para asegurarse que

la aguja salva el agujero de la plancha.

• Asegúrese de no utilizar una anchura de

punto mayor que la recomendada al coser
con aguja doble.

68

Advertising
This manual is related to the following products: