Infloor Standard Electric Cable - Manual (Page 2)

2
Infloor Installation Manual
Table of Contents
Phase 1: Design the System . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Phase 2: Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Items Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Phase 3: Inspect the Cable and Sensor . . . . . . . . . . . . . . . 5
Cable and Sensor Resistance Log . . . . . . . . . . . . . . . . . . . 6
Phase 4: Electrical Rough-in . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
New Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Existing Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Phase 5: Install the Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
General Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Other Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Final Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Phase 6: Finish Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
New Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Existing Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Phase 7: Install the Control . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Phase 8: Install the Floor Coverings . . . . . . . . . . . . . . . . .13
Phase 9: Install Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Phase 10: System Operation . . . . . . . . . . . . . . . . . . . . . . . . .13
Appendix 1: Types of Construction . . . . . . . . . . . . . . . . .14
Appendix 2: Typical Electrical Wiring Diagrams . . .16
Appendix 3: Connecting Multiple Cables . . . . . . . . . .18
Appendix 4: Connecting the LoudMouth
™ . . . . . . . . .19
Appendix 5: Sample Layouts . . . . . . . . . . . . . . . . . . . . . . . .20
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Installation Facts
Time to install
An average size bathroom should take
about two hours to install the cables and
about four hours to install the electrical box,
control, and power supply .
Skill level
Installation must be performed by quali-
fied persons, in accordance with local codes,
ANSI/NFPA 70 (NEC Article 424) and CEC Part
1 Section 62 where applicable .
Prior to installation please consult the
local codes in order to understand what is
acceptable . To the extent this information
is not consistent with local codes, the local
codes should be followed . However, electrical
wiring is required from a circuit breaker or
other electrical circuit to the control . It is rec-
ommended that an electrician perform these
installation steps . Please be aware local codes
may require this product and/or the control
to be installed by an electrician .
Expected floor temperature
The floor temperature attainable is depen-
dent on how well the floor is insulated, the
temperature of the floor before start up, and
in the case of uninsulated slab applications,
the thermal drain of the underlying materials .
These are the three most common installa-
tions:
1. Wood framing: With the cable
installed on a well-insulated wood subfloor,
and thin-set mortar and tile on top, most
floors can be heated up to 20°F warmer than
they would otherwise be .
2. Insulated concrete slab: With the
cables installed on an insulated concrete slab,
and thin-set mortar and tile on top, most
floors can be heated up to perhaps 15°F
warmer than they would otherwise be .
3. Uninsulated concrete slab: With the
cables installed on an uninsulated concrete
slab, and thin-set mortar and tile on top, most
floors can be heated up to perhaps 10°–15°F
warmer than they would otherwise be .
Please consult a designer or the factory if
questions remain about the surface tempera-
ture that can be expected from the cables in
any particular construction . Please see “Phase
9: Install Insulation” on page 13 .
Welcome to Infloor Electric Cable
Infloor Electric Cable is a simple, economical way to
warm any floor, and provide years of lasting comfort .
This instruction manual provides complete details, sug-
gestions, and safety precautions for installing this floor-
warming system .
Fasten the cables to the floor . Then, depending on the
floor coverings to be used, put down a layer of thin-set,
thick-set, or self-leveling mortar on top of the cables .
Finally, install the floor coverings . It’s that simple!
Specifications:
Infloor Electric Cable is a complete heating cable consisting of a series resistance heating cable and single power
lead for easy single-point connection. The heating cable cannot be cut to fit.
Voltages: 120, 240 VAC, 1-phase
Watts: 10 W/sqft (34 Btu/h/sqft) when spaced 3 inches on center, up to 15 W/sqft (51 Btu/h/sqft) when spaced 2
inches on center (see Table 1)
Maximum heater current: 10 amps
Maximum circuit load: 15 amps
Maximum circuit protection: 20 amps breaker
GFCI: (Ground Fault Circuit Interrupter) required for each circuit (included in the Infloor control)
Listing: UL Listed for U.S. and Canada under UL 1673 and CAN/CSA C22.2 No. 130-03, File No. E185866
Application: (-X) - (see UL Label on product) For indoor floor heating application only.
(-W) - (see UL Label on product) Wet Rated for use in wet locations per this manual.
Embedded in polymer-modified cement based mortar only (see Appendix 1).
Minimum bend radius: 1 inch
Maximum exposure temperature: (continuous and storage) 194ºF (90ºC)
Minimum installation temperature: 50ºF (10ºC)