English – Marantz SR9600N User Manual

Page 46

Advertising
background image

42

ENGLISH

3-4 NEO:6 PARAMETER

The DTS NEO:6 mode enables a maximum 6.1
channel output with just 2 channel input. (It also
supports 5.1 channel input.)
This mode expands the sound image from the
center channel.

1.

Select “3. SURROUND SETUP” from MAIN
MENU with the or cursor buttons and
press the OK/ENTER button.

2.

Select “NEO:6 PARAMETER” with the or
cursor buttons.

3.

Press the OK/ENTER button to enter the
selection.

4.

Set the CENTER GAIN level between 0.0 and
1.0 in 0.1 level increments with the or
cursor buttons.

After you complete this portion of the setup, move
cursor to “RETURN” with the , , and cursor
buttons and press the OK/ENTER button.

Notes:

• This parameter can only be set in the NEO:6-

Music mode.

• If “NONE” was selected for the center speaker

setting in the SPEAKER SIZE menu, this setting
is disabled.

SUB W LEVEL:

Set the effect level of the subwoofer speaker
between –18 and +12 level in 0.5 level interval .

• If “NONE” was selected for the subwoofer

speaker setting in the SPEAKER SIZE, then this
setting will not appear.

Note:

Setting to a mode other than multichannel stereo
or CSII will affect the speaker level as explained
in "2-2 MANUAL SETUP".

After you complete this portion of the setup, move
the cursor to “RETURN” with the , , and
cursor buttons and press the OK/ENTER button to
go to the 3. SURR SETUP menu.

3-2 PL

IIx (PRO LOGIC IIx) MUSIC PARAMETER

Pro Logic

II

x-Music mode creates a rich and

enveloping surround ambience from stereo
sources such as CDs.
In this

mode, the SR9600 includes three controls

to fine-tune the sound field as follows.

1.

Select “3. SURR SETUP” in MAIN MENU with

or cursor buttons and press the OK/

ENTER button.

2.

Select “PL

II

x MUSIC PARAMETER” with the

or cursor buttons.

3.

Press the OK/ENTER button to enter the
selection.

PARAMETER:

Select “DEFAULT” or “CUSTOM” with the or

cursor buttons.

If you select “CUSTOM”, you can adjust three
parameters as listed below.

PANORAMA:

Select the PANORAMA mode “ON” or “OFF
with the or cursor buttons.
Panorama wraps the sound of the front left and right
speakers around you, for an exciting perspective.

DIMENSION:

Set the DIMENSION level between –3 and +3
level in 1 level intervals with the or cursor
buttons.
Adjust the sound field either towards the front or
towards the rear.
This can be useful to help achieve a more
suitable balance from all the speakers with
certain recordings.

CENTER WIDTH:

Set the CENTER WIDTH level between 0 and 7
in 1 level intervals with the or cursor
buttons.
Center width allows you to gradually spread the
center channel sound into the front left and right
speakers.
At its widest setting, all the sound from the
center is mixed into the left and right speakers.
This control may help achieve a more spacious
sound or a better blend for the front image.

If “NONE” was selected for the center speaker
setting in the SPEAKER SIZE menu, this setting
cannot be selected.

After you complete this portion of the setup, move
cursor to “RETURN” with the , , and cursor
buttons and press the OK/ENTER button.

3-3 CS

II/TS XT PARAMETER

1.

Select “3. SURROUND SETUP” from MAIN
MENU with the or cursor buttons and
press the OK/ENTER button.

2.

Select “CS

II

/TS XT PARAMETER” with the

or cursor buttons.

3.

Press the OK/ENTER button to enter the
selection.

TRUBASS:

Set the TRUBASS level between 0 and 6 in 1-
level increments with the or cursor buttons.
TRUBASS produced by the speakers are an
octave below the actual physical capabilities of the
speakers adding exciting, deeper bass effects.

SRS DIALOG:

Set the SRS DIALOG level between 0 and 6 in
1- increments with the or cursor buttons.
This can be popped out of the surround audio
effects, allowing the listener to easily discern what
the actors say.
If “NONE” was selected for the center speaker
setting in the SPEAKER SIZE menu, this setting
cannot be selected.

After you complete this portion of the setup, move
cursor to “RETURN” with the , , and cursor
buttons and press the OK/ENTER button.

Note:

• This parameter can only be set in the CSII and

Virtual (TruSurround XT) modes.

P L II x

M U S I C

P A R A M E T E R

P A R A M E T E R

:

C U S T O M

P A N O R A M A

: O F F

D I M E N S I O N

: - 3

C E N T E R W I D T H :

3

R E T U R N

E X I T

C S

II / T S

X T

P A R A M E T E R

T R U B A S S

:

0

S R S

D I A L O G

:

0

R E T U R N

E X I T

N E O : 6

P A R A M E T E R

C E N T E R

G A I N

:

0 . 0

R E T U R N

E X I T

SR9600N DFU_01_ENG 3_4

05.5.23, 5:48 PM

Page 42

Adobe PageMaker 6.5J/PPC

Advertising
This manual is related to the following products: