Troubleshooting – Marantz SR9600N User Manual
Page 68
ENGLISH
64
TROUBLESHOOTING
In case of trouble, check the following before calling for service:
1.
Are the connections made properly?
2.
Are you operating the unit properly following the user’s guide?
3.
Are the power amplifiers and speaker working properly?
If the unit does not operate properly, check items shown in the following table.
If your trouble cannot be recovered with the remedy actions listed in the following table, malfunction of the
internal circuitry is suspected; immediately unplug the power cable and contact your dealer, nearest
Marantz authorized dealer or the Marantz Service Center in your country.
CAUSE
The power plug is not connected.
Mute is on.
The input cable is not connected
correctly.
The master volume control is turned all
the way down.
The function selector position is wrong.
The headphones are connected to the
headphone jack.
The input cable is connected incorrectly.
The speaker cable is connected incorrectly.
The center speaker cable connection is
incomplete.
STEREO has been selected for the
Surround mode.
Center = NONE has been selected in
SETUP mode.
The surround speaker cable connection
is incomplete.
STEREO has been selected for the
Surround mode.
Surround = NONE has been selected in
the SETUP mode.
The surround back speaker cable
connection is incomplete.
The surround mode is not EX/ES mode.
Surround back = NONE has been
selected in the SPEAKER SIZE menu.
SYMPTOM
The SR9600 cannot be turned on.
No sound and picture are
output even when power is on.
No speaker output.
Incorrect audio or video for
selected source.
Incorrect audio from a channel.
No audio is output from the
center channel speaker.
No audio is output from the
surround speakers.
No audio is output from the
surround back speakers.
REMEDY
Connect the power plug to the outlet.
Cancel mute using the remote control unit.
See the connection diagram and connect the
cables correctly.
Adjust the master volume.
Select the correct position.
Disconnect the headphones. (Speakers will not
output sound when headphones are connected.)
Connect the cable correctly by referring to the
connection diagram.
Connect the cable correctly by referring to the
connection diagram.
Connect the cable correctly.
When STEREO is selected for the Surround mode,
no sound will be output from the center speaker.
Set another Surround mode.
Make the correct setting.
Connect the cable correctly.
When STEREO has been selected for the
Surround mode, no sound will be output from the
surround speaker. Set another Surround mode.
Make the correct setting.
Connect the cable correctly.
Set surround mode EX/ES.
Make the correct setting.
Note:
• After “PROTECT” appears on the unit’s display, the standby indicator may start flashing. If it does, there is a
problem in the unit or the connection. If this problem reoccurs even when power is activated from the remote
control unit, call for servicing.
SYMPTOM
Cannot select the EX/ES or
THX EX mode.
Cannot select THX ULTRA 2
CINEMA MUSIC, GAMES.
Cannot select the Neo:6
mode.
Ca not select the CS
II
mode.
No output to SUBWOOFER
OUT.
Noise is produced during DTS-
encoded CD or laserdisc play.
A specific channel does not
produce output.
AM or FM reception fails.
Noise is heard during AM
reception.
Noise is heard during FM
reception.
Cannot get programmed
station when the PRESET
button is pressed.
Control with the remote
control unit fails.
MRAC is not working.
CAUSE
Surround Back = NONE has been
selected in the SPEAKER SIZE menu.
The input signal is incompatible.
Surround Back = 1ch, NONE has been
selected in the SPEAKER SIZE menu
The input signal is incompatible.
The input signal is incompatible.
The input signal is incompatible.
Subwoofer = NONE has been selected
in the Setup mode.
Analog has been selected for input.
Nothing recorded on source.
Antenna connection is incomplete.
Reception is affected by other electrical
fields.
The radio waves from the broadcasting
station are weak.
Preset data has been erased.
Batteries are exhausted.
Remote control unit function key setting
is wrong.
The distance between the SR9600 and
the remote control unit is too far.
Something is blocking the SR9600 and
the remote control unit.
Headphones are connected.
REMEDY
Make the correct setting.
Use a 5.1channel source.
Make the correct setting.
Use a 5.1channel source.
Use a 2 channel Dolby Digital input signal, PCM
input signal or analog input signal.
Use a 2 channel Dolby Digital input signal, PCM
input signal or analog input signal.
Select Subwoofer = YES.
Be sure to perform digital connection, select digital
input, then play.
Check the encoded channel on the source side.
Correctly connect the indoor AM and FM antennas
to AM and FM antenna outlets.
Try changing the location where the AM indoor
antenna is set up.
Install an FM outdoor antenna.
Disconnecting power plug for long periods of time
will erase preset data. If this happens, input the
preset data again.
Replace all the batteries with new ones.
Select a different position from which equipment
will be controlled.
Move closer to the SR9600.
Remove the offending object.
Disconnect the headphones.
SR9600N DFU_01_ENG 4_4
05.5.23, 5:58 PM
Page 64
Adobe PageMaker 6.5J/PPC