Desa VMH10TPC - Manual (Page 28)

www.desatech.com 112462-01F 28
Key Pad Lock Feature
This feature allows the user to lock/unlock
the keypad on the hand-held remote in the
MANU or AUTO mode to prevent inadvertent
operation (i.e. children operating the hand-held
remote control, etc.). The keypad is locked in
either on or off. Press the POWER and LOCK
buttons together to turn the unit on or off.
OPERATING FIREPLACE
Continued
Figure 44 - Thermostat Hand-Held
Remote Control Unit
GWMT1 WALL MOUNTED
THERMOSTAT (OPTIONAL)
Make sure the heater switch is on REMOTE
and set the temperature adjustment on wall
thermostat to the desired setting. The thermo-
stat has been electronically calibrated at the fac-
tory and requires no adjustment or leveling.
Upon installation, the thermostat must be al-
lowed to stabilize at room temperature for a
minimum of 30 minutes for proper operation.
See installation instructions on page 22 of this
manual.
GWMS2 WALL MOUNTED
SWITCH (OPTIONAL)
Make sure the heater switch is on REMOTE.
This wall switch works just like the conven-
tional light switch. Flip the switch up for on
and down for off.
Note:
Make sure that this switch is not in a
position to be mistaken for a light switch. This
may result in the fireplace being inadvertently
turned on without the proper precautions being
taken. See installation instructions on page 23
of this manual.
THERMOSTAT SERIES (MODEL
HRC200 AND HRC201)
The hand-held remote can be operated using
either the manual mode (MANU) or thermo-
static mode (AUTO) (see Figure 44). To select
Fahrenheit/Centigrade mode display, carefully
press the ˚C/˚F mode button with the end of a
paper clip or similar blunt object.
Manual Mode
1. Press the POWER and LOCK buttons
together to turn on the hand-held remote
control.
2. Press the MANU button to turn on the
fireplace.
3. Press the POWER and LOCK buttons
together to turn off the fireplace.
Auto (Thermostatic) Mode
1. Press the POWER and LOCK buttons
together to turn on the hand-held remote
control.
2. Press AUTO button to select this mode.
3. Set the desired room temperature by press-
ing the TEMP + or - buttons.
4. Press the POWER and LOCK buttons
together to turn off the fireplace
Note: Do not leave the hand-held remote in the
AUTO mode close to the fireplace. The radiant
heat from the fireplace will turn off the fireplace.
Ideally, place the hand-held remote in the center
of the room facing towards the fireplace.
Note:
Do not hold the hand-held remote for
a long time. Body temperature will affect its
operation in the AUTO mode.
Safety Features
When away from home for an extended period of
time or as a child safety feature to prevent accidental
ignition of the fireplace, receiver ON/OFF/REMOTE
switch should be in the OFF position.
Auto Shutoff Feature
1. If the average room temperature exceeds 82°
Fahrenheit (28° Centigrade), the hand-held
remote control will perform a safety override
and shut the fireplace off. This feature is not
available in the MANU mode.
2. The receiver continuously receives signals
from the hand-held remote to control the
room temperature. If the hand-held remote
is misplaced, obstructed or for any reason
cannot transmit to the receiver, the receiver
will shut off the fireplace after 8 minutes.
LOCK
MANU AUTO
ºC/ºF
TEMP
POWER
ROOM
TEMP SET
TEMP
AUTO
Turns
Hand-Held
Remote On
or Off and
Allows You
to Choose
the Manual
Setting
Selects
AUTO
Mode °C/°F
Mode
Button
Locks
System to
Prevent
Accidental
Ignition
Turns
Burners
On or
Off
Increases
or Decreases
Room
Temperature
in AUTO Mode
Digital
Display
Shows
Temperature
and Settings