Document Outline

• Operating, Maintenance and Installation Instructions
• Table of Contents
• Important Safety Information
  • PTO-Specific Hazards
  • Look for Safety Symbol
  • Be Aware of Signal Words
  • Using PTO Safely
  • Prepare for Emergencies
  • Be Familiar with Safety Decals
  • Avoid High Pressure Fluids
  • Practice Safe Maintenance
  • Safety At All Times
  • Safety Decals
    • Safety Decals
    • Danger Decals
    • 858-005C
    • Danger: Rotating Driveline
    • Warning Decals
    • 858-004C
    • Warning: Hot Fluid
    • Caution Decals
    • 818-130C
    • Caution: 540 RPM PTO
    • 818-240C
    • Caution: 1000 RPM PTO
• Introduction
  • Description of Unit
    • Suitable Applications
  • Kits Covered
  • Related Documents
  • Related Parts
    • 20-Spline Coupler
    • 21-Spline Coupler
  • Using This Manual
    • Definitions
    • Call-Outs
  • Owner Assistance
• PTO Operation
  • Tractor Requirements
    • 540 rpm Tractor Requirements
      • 540 rpm PTO Clearance
    • 1000 rpm Tractor Requirements
      • 1000 rpm Type 2 PTO Clearance
      • 1000 rpm Type 3 PTO Clearance
  • Hitching with PTO
    • Hitching with 540 rpm PTO
      • Prepare Tractor
      • Mount Pump
      • Secure Pump
    • Hitching with 1000 rpm PTO
      • Install Coupler
      • Prepare Tractor
      • Mount Pump
  • Check Hydraulics
    • Check Oil Level
    • Inspect Hoses and Fittings
  • Starting the Pump
  • About the Flow Control Valve
  • Setting Meter Pressurization
    • General Steps for all Kits
    • Ground Drive Meter Pressure
    • Hydraulic Drive Meter Pressure
      • Adjustment Steps:
  • PTO Unhitching
    • Dismount 540 rpm Pump
    • Dismount 1000 rpm Pump
• PTO Troubleshooting
• PTO Maintenance
  • Oil and Filter Change
    • Oil Fill
      • Oil Specification
    • Oil and Filter Change
  • Lubrication and Scheduled Maintenance
    • Oil Filter
    • Pump/Fan Oil
    • 540 rpm Seal Kit
    • 1000 rpm Seal Kit
• Appendix A - Installation
  • Before You Start
  • Compatible Planters
    • One PTO pump kit is always required. Older planters may also require a fan update kit. Each kit updates one planter.
    • Fan Motor Compatibility
    • Configuration Compatibility
    • 2025A/2525A Compatible Kits
    • YP425A Compatible Kits
    • YP625A Compatible Kits
    • YP825A/AR Compatible Kits
    • Other Single-Section Air-Pro® Implements
  • Tools Required
    • Call-Outs
  • Pre-Delivery and Other Options
  • Prepare Planter
  • Prepare Fan
    • Disconnect Existing Fan Hoses
      • Disconnect 2-Port Fan
      • Disconnect 3-Port Fan
    • Open Fan Screen
    • Dismount or Relocate Sensor Bracket
    • Update Fan Motor
      • Recover Motor Fittings
      • Release Impeller
      • Dismount Fan
      • Remove 3-Port Hydraulic Motor
      • Mount 2-Port Hydraulic Motor
      • Re-Mount Fan
      • Install New Impeller Bushing
      • Install Motor Fittings and Loop
      • Re-Mount Fan Inlet Screen
      • Re-Install RPM Sensor Bracket
  • Install Fan Cooler
    • Install Fan Cooler
      • Break Down Cooler Assembly
      • Install Cooler Shroud
      • Orient Cooler Elbows
      • Re-Assemble Fan Cooler
      • Modify Fan Cage
      • Attach Cooler Hoses & Close
  • Reconnect Hitch Hoses
  • Install Oil Reservoir
    • Determine Reservoir Location
    • Reservoir on Row Unit Tool Bar
      • Identify Row Location
      • Support Row Unit
      • Mount Row Unit Reservoir
    • Reservoir on Fertilizer Sub-Frame
    • Reservoir on Mainframe Truss
    • Reservoir Under Main Seed Box
    • Reservoir on Tongue at Hitch
  • Install Flow Control Valve
    • Determine Control Location
    • Install Controls on Fan Mast
    • Install Controls on Fertilizer Frame
    • Install Controls on Upper Frame Tube
    • Install Controls on Forward Tool Bar
  • Install Hoses
    • General Hose Installation
    • 401-845A and 411-163A Flow Control Hydraulics
    • 401-846A and 411-164A Flow Control Hydraulics
    • 401-847A and 411-165A Flow Control Hydraulics
    • 401-848A and 411-166A Flow Control Hydraulics
    • 401-849A and 411-167A Flow Control Hydraulics
    • 401-879A and 411-168A Flow Control Hydraulics
    • 411-016A Flow Control Hydraulics
      • Connect Hoses
    • 411-035A and 411-036A Flow Control Hydraulics
    • 411-037A and 411-038A Flow Control Hydraulics
      • Replace/Add Fittings
      • Connect Remaining Hoses
  • Charge and Test
  • Close-Out
• Appendix R - Reference
  • Torque Values
    • Hydraulic Fitting Torque
      • Connector Identification
  • Abbreviations
  • Parts Lists
    • Kits and This Manual
    • New Parts in Kits
    • Existing Parts Affected
• Index