Sony XDCAM HD PDW-HD1500 - Manual (Page 54)

54
Playback
C
h
ap
te
r 4
R
e
c
o
rd
in
g
an
d
P
la
y
ba
c
k
To set shot marks
While playing back a disc, you can set essence marks such
as Shot Mark1 and Shot Mark2 in desired frames.
To set a Shot Mark1 or Shot Mark2, hold down the
V/
MARK1 or v/MARK2 button and press the PUSH
SET(S.SEL) knob.
Use the PDZ-1Proxy Browsing Software on the supplied
XDCAM Application Software CD-ROM to delete and
modify essence marks.
See page 143 for an overview of the PDZ-1 software and
information about how to install it.
You can also delete and modify essence marks from the
Thumbnail Menu of the chapter thumbnail screen (see
page 65).
To set a clip flag
You can set one of the three types of flag (OK, NG or
KEEP) for the clip while it is being played back by
viewing its video image and using the function menu (see
page 45).
Playback in jog mode
In jog mode, you can control the speed of playback by the
speed of turning the jog dial. The playback speed range is
–1 to +1 times normal speed.
To carry out playback in jog mode, proceed as follows.
1
Press the SHTL/JOG button or VAR/JOG button,
turning it on.
2
Turn the jog dial in the desired direction, at the speed
corresponding to the desired playback speed.
Playback in jog mode starts.
3
To stop playback in jog mode, stop turning the jog dial.
When setup menu item 101 SELECTION FOR
SEARCH DIAL ENABLE is set to “dial” (factory
default setting), you can start jog playback by simply
rotating the jog dial, even when the SHTL/JOG and
VAR/JOG buttons are not lit.
Playback in shuttle mode
In shuttle mode, you can control the speed of playback by
the angular position of the shuttle dial. The range of
playback speed is ±20 times normal speed.
To carry out playback in shuttle mode, proceed as follows.
1
Press the SHTL/JOG button, turning it on.
2
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
Playback in shuttle mode starts.
3
To stop playback in shuttle mode, return the shuttle
dial to the center position, or press the STOP button.
When setup menu item 101 SELECTION FOR
SEARCH DIAL ENABLE is set to “dial” (factory
default setting), you can start shuttle playback by
simply rotating the shuttle dial, even when the SHTL/
JOG button is not lit.
To alternate between normal-speed playback and
shuttle mode playback
Set the shuttle dial to the position corresponding to the
desired shuttle playback speed, then switch between
normal-speed playback and shuttle playback by pressing
the PLAY and SHTL/JOG buttons alternately.
Playback in variable-speed mode
In variable-speed mode, you can control the speed of
playback in the range of –2 to +2 times normal speed. (You
can use setup menu item 119 VARIABLE SPEED LIMIT
IN KEY to specify the speed range of variable playback.)
To carry out playback in variable-speed mode, proceed as
follows.
REC NET
REMOTE
LOCAL
VARIABLE KEY INHI
PRE- SET
ON
OFF PB
PHONES LEVEL
SHIFT
DISPLAY
HOME
PAGE
EXPAND
CHAPTER
TOP F REV F FWD END STANDBY REC INHI
PREV NEXT PLAY STOP REC THUMBNAIL
RETURN
PUSH SET(S.SEL)
MENU
RESET
MARK2
MARK1
IN OUT
SHTL/JOG
SUB CLIP
DISC MENU
VAR/JOG
EJECT
ACCESS
CH-1
ALL CH
CH-2
CH-3
CH-4
2,3 1 1
REC NET
REMOTE
LOCAL
VARIABLE KEY INHI
PRE- SET ON
OFF PB
PHONES LEVEL
SHIFT
DISPLAY
HOME
PAGE
EXPAND
CHAPTER
TOP F REV F FWD END STANDBY REC INHI
PREV NEXT PLAY STOP REC THUMBNAIL
RETURN
PUSH SET(S.SEL)
MENU
RESET
MARK2
MARK1
IN OUT
SHTL/JOG
SUB CLIP
DISC MENU
VAR/JOG
EJECT
ACCESS
CH-1
ALL CH
CH-2
CH-3
CH-4
2,3 3 1