KORG Professional Engineer PA3 - Manual (Page 112)

110 Effects
EQ and Filters (EQ/Filter)
c: Threshold
d: Attack
d: Release
“Threshold” specifies the level at which gating occurs when
“Envelope Select” is set to L/R Mix, L Only, or R Only.
“Attack” and “Release” specify the attack time and release time of
the gate.
c: Polarity
This inverts the polarity of the gate on/off operation. With the
“–” setting, the gate will close when the input signal exceeds the
specified level. The direction in which the modulation source
opens or closes the gate will also be reversed.
e: Delay Time [msec]
This sets the delay time for the input to the gate. When using
shorter Attack Time settings, you can lengthen the Delay Time
so that the sound is input after the gate opens.
EQ and Filters (EQ/Filter)
7: St.Parametric4EQ
(Stereo Parametric 4-Band EQ)
This is a stereo 4-band parametric equalizer. You can select
peaking type or shelving type for Band 1 and 4. The gain of Band
2 can be controlled by dynamic modulation.
c
Threshold 0...100
Sets the level at which gating is
applied
Polarity +, – Switches the polarity of gating
d
Attack 1...100 Sets the attack time
Release 1...100 Sets the release time
e
Delay Time
[msec]
0...100
Sets the delay time for the gate
input
f
Side PEQ Insert Off, On
Switches the trigger signal equalizer
on/off
Trigger
Monitor
Off, On
Switches between monitoring the
effect output and the trigger signal
g
Side PEQ
Cutoff [Hz]
20...12.00k
Sets the center frequency of the
equalizer for the trigger signal
Q 0.5...10.0
Sets the bandwidth of the equalizer
for the trigger signal
Gain [dB] –18.0...+18.0
Sets the gain of the equalizer for the
trigger signal
h
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Input Level
Output Level
Threshold
Louder
Louder
Threshold
Attack=1
Release=1
Attack=100
Release=100
Dry
Wet
Wet
Attack Release
Gate - Attack / Release
Gate - Threshold
a Trim 0...100 Sets the input level
b Band1 Type
Peaking,
Shelving-Low Selects the type of Band 1
c Band4 Type
Peaking,
Shelving-High
Selects the type of Band 4
d
Band2
Dynamic Gain
Src
Off...Tempo
Selects the modulation source of the
Band 2 gain
Amt [dB] –18.0...+18.0
Sets the modulation amount of
Band 2 gain
e
Band1 Cutoff
[Hz]
20...1.00k Sets the center frequency of Band 1
Q 0.5...10.0 Sets the bandwidth of Band 1
Gain [dB] –18.0...+18.0 Sets the gain of Band 1
f
Band2 Cutoff
[Hz]
50...10.00k Sets the center frequency of Band 2
Q 0.5...10.0 Sets the bandwidth of Band 2
Gain [dB] –18.0...+18.0 Sets the gain of Band 2
g
Band3 Cutoff
[Hz]
300...10.00k Sets the center frequency of Band 3
Q 0.5...10.0 Sets the bandwidth of Band 3
Gain [dB] –18.0...+18.0 Sets the gain of Band 3
h
Band4 Cutoff
[Hz]
500...20.00k Sets the center frequency of Band 4
Q 0.5...10.0 Sets the bandwidth of Band 4
Gain [dB] –18.0...+18.0 Sets the gain of Band 4
i
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
Stereo In - Stereo Out
Band1 Band2 Band3 Band4
PEQ PEQ PEQ PEQ
LEQ
LEQ
HEQ
HEQ
PEQ PEQ PEQ PEQ
Trim
Trim
D -mod